Handleiding Scheppach LS40P Woodster (pagina 18 van 32) (Duits, Engels, Frans)

782006

Verklein

Vergroot

Pagina terug

1/32

Pagina verder

18 GB

Adjusting the scarifying depth (Fig.12)

The scarifying depth is set using the depth adjustment

(11). To do this, pull the depth adjuster (11) slightly to the

right and bring it into the desired position and let it snap

into place.

+1 = driving or transport position

0 = 0 mm

-1 = Scarifying depth -2,5 mm

-2 = Scarifying depth -5 mm

-3 = Scarifying depth -7,5 mm

-4 = Scarifying depth -10 mm

-5 = Scarifying depth -12,5 mm

-6 = Scarifying depth -15 mm

Operation

Important!

The engine does not come with oil in it. Therefore,

be sure to add oil before starting the engine. The

oil level in the engine must be checked each time

before carrying out any work.

Starting the equipment

In order to avoid any unintentional start-ups of the

engine, it comes equipped with an engine brake

(Fig. 1/Item 1) which must be pressed at all times

whilst the device is in use, otherwise the engine

will stop. Important: When the engine brake lever is re-

leased it must return to its initial position and the engine

must stop. If this is not the case, do not use the equip-

ment again.

1. Open the petrol cock (Fig. 14 / Item B). Set the

cock to “ON” for this purpose.

2. Set the choke lever (Fig. 14/Item A) to the “Choke”

position. Note: Normally the choke is not required

to restart a warm engine.

3. Move the throttle lever (Fig. 13 / Item 3) to the cen-

tre position.

4. Press the engine brake lever (Fig. 13) and pull the

starter cable (Item 14) forcefully until the engine

starts.

5. Allow the engine to warm up briey and then set

the choke lever (Fig. 13 / Item A) to the “RUN” Posi-

tion.

6. The speed of the cutter unit can be controlled using

the throttle lever (Fig. 13 / Item 3).

Important: Always pull the starter cable slowly

until you feel the initial resistance before you then

pull it quickly to start the engine. Do not allow the

starter cable to whip back of its own accord.

Important: The scarier roller begins to rotate as soon

as the engine is started.

Important! Never open the ejector ap when the motor

is running. A rotating cutting unit can cause injuries.

Always fasten the ejector ap carefully. The ap ips

back to the “Closed” position by the tension springs!

Always ensure that a safe distance (provided by the long

Information concerning noise emission measured

according to relevant standards:

Sound pressure LpA = 85,4 dB(A)

Sound power LWA = 98 dB(A)

Uncertainty KPA = 2 dB(A)

Wear ear-muffs. The impact of noise can cause

damage to hearing.

Vibrations:

Vibration Ahv (left/right) = 6,74 m/s2

Uncertainty KPA = 1.5 m/s2

Keep the noise emissions and vibrations to a mini-

mum.

• Only use appliances which are in perfect working or-

der.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical

to the mains data.

Warning!

The scarier is delivered unassembled. The grass bas-

ket and the complete push bar must be assembled and

mounted before using the scarier. Follow the operating

instructions step-by-step and use the pictures provided

as a visual guide to easily assemble the machine.

Montage

n Important!

You must fully assemble the appliance before using

it for the rst time!

Mounting of the guide rail (Fig. 3 - 9)

• Mount the lower push bar (4) as shown in pictures

3 + 4. Fix the bracket with four hexagon bolts and

the locknuts (E).

• Connect the upper push bar (handle) (1) to the

lower push bar (4). Use the two wing nuts with the

respective screws (5) (Fig. 5 + 6).

• Attach the cable pull retainer (B) to the right side of

the handlebar as shown in Figure 7.

• Fix the cables with the two cable clamps (A) on the

push handle. (Figure 8 + 9)

Mounting the grass catcher (Fig. 10 - 11)

• Lift the ejection ap (Fig. 11 / Item 7) with one hand

and hook in the catching basket (Fig. 11 / Item 6)

with the other hand on the handle from above. At-

tention! To hang the grass catcher, the engine must

be switched off and the roller must not turn!

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scheppach LS40P Woodster Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info