21GB
6. Technical data
LB5200BP
Technical data
Dimension LxWxH mm 1380x400x450
Air speed max. km/h 295
air volume max. m3/min 18
dust bag capacity l -
Power unit
Displacement cm351,7
Max. engine output kW 1,4
Idle speed min-1 3500 ± 300
Fuel tank capicity cm31000
Engine type 2-stroke engine, air-cooled
Weight kg 7,84
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure LpA = 94,0 dB(A)
Sound power LWA = 110 dB(A)
Uncertainty KPA = 3 dB(A)
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration Ahv = 1,655 m/s2
Uncertainty KPA = 1.5 m/s2
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves.
In these operating instructions we have marked the
places that have to do with your safety with this sign:
7. Attachment and operation
ATTENTION! Before working on the device - cleaning,
inspection, maintenance or other work - always turn off
the device.
ASSEMBLY
The blower must not be used or switched on until
it has been fully assembled.
Assembly (Fig6-6c)
• Attach the two hose clamps (17A and 17B) to the e-
xible blowpipe (12).
• Push the exible blowpipe (12) over the connection to
the motor unit and tighten the hose clamp (17B) rmly
(Fig. 6).
• Now push the handle (1) over the upper blowpipe (13).
Align the handgrip (1) and the guide in the same way,
fold it together and then tighten it (Fig. 6a).
• Push the upper blowpipe into the exible blow hose
(12) with the handle and x it with the hose clamp (17A)
(Fig. 6b).
• Push the lower blowpipe (14) over the upper blowpipe
(13) and lock it in the clockwise direction (Fig. 6c)
• The blower nozzle (No. 15) is simply pushed over the
lower blowpipe (No. 14) and locked in the clockwise di-
rection (Fig. 6c).
Warning! Use only original manufacturer‘s replace-
ment parts, accessories and attachments. Failure to
do so can cause poor performance, possible injury and
may void your warranty. Never use the machine wit-
hout the guard assembled!
Operation
Before starting
Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that the
safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
Place the carrying strap
Pull the belt down, the straps are tightened
Loosen the straps
Lift the clamping slide
Adjust the carrying strap so that the back plate rests rm-
ly and securely against t
Fuel and oil
Recommended fuels
Use only a mixture of unleaded petrol and special 2-stro-
ke engine oil. Mix the fuel mixture as indicated in the fuel
mixing table.
Important: Do not use a fuel mixture which has been
stored for longer than 90 days.
Important: Never use 2-stroke oil with a recommended
mixing ratio of 100:1. The manufacturer’s warranty
will be voided in case of engine damage due to inade-
quate lubrication.
Important: Only use containers designed and approved
for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil into
the mixing bottle (see scale printed on the bottle). Then
shake the bottle well.
Never use oil for 4-cycle engine or use water cooled
2-cycle engine. It can cause spark plug fouling exhaust
part blocking or piston ring sticking.
Mixed fuels, which have been left unused for a period of
one month or more, may clog the carburetor or result in
the engine foiling to operate property. Put remained fuel
into an airtight container and keep it in the dark and cool
room.
