782080
47
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
DGB
46
7. BENUTZUNG DER MASCHINE
h. Abrichthobeln von Werkstücken
1. Hobeln eines Probestücks (34)
7. PUTTING THE MACHINE INTO OPERATION
h. Surface planing
1. Planing of a piece (34)
- Vor dem ersten Gebrauch wischen Sie das Anti-Korrosions-
mittel mit Petroleum von der Hobelwelle (Verwenden Sie kein
Benzin).
- Der Dickentisch (D) muss eingestellt werden um den
Absaugstutzen zu montieren (F). (33)
- fahren Sie den Dickentisch mit dem Handrad (M1) nach
oben, um den Absaugstutzen (F) unter dem Ausganstisch (B)
gut zu spannen.
- Kuppeln Sie den Einzugshebel für Bretter (Y) aus, damit
sich die Antriebswalzen nicht unnötig drehen.
- Um senkrechte Flächen und Kanten zu erhalten, justieren
Sie zuvor den Winkelanschlag auf 90°. (siehe «Einstellen des
Winkelanschlags»).
Wichtig : Vergewissern Sie sich vor Beginn der Arbeit, dass
das Holz keine Äste hat, um einen gehährlichen Rückschlag
zu vermeiden.Achten Sie auch darauf, dass die Oberfläche
desHolzes nicht zu sehr gewölbt ist.
- Legen Sie die «hohle» Oberfläche des Brettes auf den
Eingangstisch (A).
- Stellen Sie den Hobelwellenschutz (G) ein (siehe «Einstel-
len des Hobelwellenschutzes»)
- Schieben Sie das Brett mit einer durchgehenden Bewegung
gegen die Hobelwelle, um Ungleichmäßigkeiten zu vermei-
den.
- Üben Sie an den Kontaktpunkten mit dem Tisch einen
Druck aus und drücken Sie mit der linken Hand den geho-
belten Anfang des Brettes auf den Ausgangstisch (B). Die
rechte Hand dient nur zum Schieben des Brettes.
- Verwenden Sie am Brettende den Schiebestock. (35)
- Wiederholen Sie den Arbeitsgang, bis eine sauber
gehobelte öberfläche entstanden ist.
- Am Ende des Durchgangs, kann das Brett auf den Ein-
gangstisch (A) zurückgeholt werden, indem man es über den
Hobelwellenschutz (G) gleiten lässt.
- Before the first use, wipe the anti-corrosion agent from the
cutter block with petroleum (do not use gasoline).
- The thicknessing table (D) must be set in order to fit the
suction connection (F). (33)
- Move the thicknessing table upwards with the hand wheel
(M1), in order to firmly clamp the suction connection (F)
underneath the ouput table (B).
- Disengage the feed lever for boards (Y) so the drive rollers
do not rotate without necessity.
- In order to get vertical surfaces and edges, first adjust the
angle guide to 90°. (see. «Setting the angle guide»)
Important : before starting work make sure that the wood
does not have any knots in order to avoid dangerous kick-
back. The work piece surface must also not be much curved.
- Put a board with the «hollow» surface on to the infeed table
(A).
- Set the cutter block guard (G). (see «setting the cutter block
guard»)
- Push the board smoothly against the cutter block in order to
avoid irregularities.
- Exerce a pressure where the board touches the table. With
your left hand, press the planed start of the board onto the
output table (B). The right hand only pushes the board.
- Use the stick at the end of the board. (35)
- Repeat the procedure until a clean planed surface is
obtained.
- At the end of the passage, the board can be returned to the
entry table (A) by letting it slide over the cutter block guard
(G).
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach KITY 439 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach KITY 439 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 1.83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info