782563
38
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
38 | GB
To change the angle of the transverse stop (19), pro-
ceed as follows:
1. Loosen the clamping handle (19c) by turning it
counterclockwise.
2. Turn the transverse stop (19) until the arrow points
to the desired angle.
3. Secure this position by turning the clamping han-
dle (19c) clockwise.
9.8 Connecting an extraction device (g. 24 + 25)
m WARNING
Danger of injury for eyes due to swirling chips
- Wear eye protection.
- Only operate the product with a suitable chip
extraction system. Do not use a common house-
hold vacuum cleaner.
1. Screw the hose clamp for the extraction hose (23)
into the right table width extension (9) using a
Phillips screw M5 x 10mm (F), two small washers
(H) and a nut M5 (M). (g. 24)
2. Place the extraction hose (6) on the extraction
port (22) at the rear of the machine, push the ex-
traction hose (23) through the hose clamp and
attach it to the extraction port of the saw blade
guard (2). (g. 25)
3. Connect a suitable chip extraction system (not in-
cluded in the scope of delivery) to the extraction
port (22).
ATTENTION
Check and clean the extraction channels at regular
intervals.
10. Before commissioning
10.1 General notes
Check that the product is fully assembled.
Check that the safety covers are present, installed
and functional.
Check that the switches work as intended.
Check that the product is on a rm footing.
Check that the labels on the product are present and
legible. Missing or damaged labels must be replaced
or exchanged.
Check that the mains voltage and the operating volt-
age match, see Technical data.
Check that the supply lines, extensions, cable
drum, etc. are not too long. Otherwise there may
be a drop in voltage or delay in motor start-up.
Check that the ambient temperature is observed.
10.2 Product-specic notes
The machine must be securely installed.
It must be possible for the saw blade to run freely.
In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
9.5 Fitting the saw blade guard (g. 19)
1. Place the saw blade guard (2) onto the riving knife
(3) from above.so that the xing screw (2a) ts
through the hole in the riving knife.
2. Tighten the xing screw (2a).
Attention! The saw blade guard (2) must remain
free to move.
3. Ensure that the saw blade guard (2) can move
freely.
4. Disassembly takes place in reverse order.
m WARNING
Danger of injury due to incorrect tted saw blade
guard
- Before starting sawing, ensure that the saw
blade guard (2) automatically lowers onto the
material to be sawn.
9.5.1 Checking the saw blade guard
After tting, check that the saw blade guard (2) is
functioning properly.
1. Lift the saw blade guard (2) and then release it.
2. The saw blade guard (2) should automatically
move back to its starting position.
9.6 Fitting the parallel stop (g. 20)
1. First place the parallel stop (8) with open eccen-
tric lever (8b) on the rear guide rail (7a), then on
the front guide rail (7b) on the saw table (5).
2. To change the position of the parallel stop (1),
slide the parallel stop (1) with open eccentric lever
(8b) along the front and rear guide rail (7a/7b).
3. To secure the parallel stop (1) in the desired po-
sition, press the eccentric lever (8b) fully down-
wards.
9.6.1 Attaching the stop rail to the parallel stop
(g. 21 + 22)
1. Insert the two coach bolts M6 x 55 mm (E)
from the inside into the parallel stop (8) and
secure them with the two knurled nuts (G).
Attention! Do not tighten the knurled nuts (G) yet.
(g. 21)
2. Push the stop rail (8a) through the two coach
bolts (E) into the desired position and tighten the
knurled nuts (G). (g. 22)
9.7 Fitting the transverse stop (g. 23)
1. Push the transverse stop (19) into the groove (28)
of the sliding carrier plate (21).
2. Now place the guide rail (19b) including the
screws into the marked grooves of the transverse
stop (19) (g. 23).
3. Move the guide rail (19b) into the desired position
and tighten the knurled nut (19d).
4. Screw the clamping handle (19c) into the trans-
verse stop (19) by turning it clockwise.
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HS116 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HS116 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 6.03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info