781866
30
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58 www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
30 | GB
Draining the fuel tank (g: S + Z)
Have a suitable container ready and open the drain
plug (t) of the oat chamber (g. Z). Now remove the
tank cap (12) and open the fuel tap (11). The system is
then completely empty. Close the tank cap (12) again.
Cleaning / replacing the air lter (g O - Q)
Unscrew the wing nut (o) and remove the air lter
cap (n)
Check the air lter cap (n) for holes and cracks. Re-
place the damaged element.
Unscrew the inner wing nut (p) and carefully pull out
the paper lter insert (s) with the foam lter insert
(r).
Wipe off dirt on the inside of the lter housing with
a clean moist cloth. Make sure that no direct en-
ters the opening. Set the air lter cap (n) on the
lter housing for the duration of the lter cleaning
process.
Carefully remove the foam lter insert (r) from the
paper lter insert (s). Check both parts for damage.
Replace the damaged inserts.
Clean the foam lter insert (r) in warm water and
a mild soap solution. Thoroughly rinse it out with
clear water and let it dry completely.
Immerse the foam insert (r) into clean engine oil
and press out the excess oil.
Securely knock the paper lter insert (s) on a hard
surface to remove the dirt. Never brush out the dirt,
since it is pressed into the bre.
Set the foam insert (r) on the paper lter insert (s)
and install the air lter element with the seal again.
Screw the rst wing nut (p) on the paper lter insert.
Mount the air lter cap (n) and fasten the second
wing nut (o).
m ATTENTION!: Never run the engine without or
with a damaged air lter insert. This would allow dirt
to enter the engine, which would damage the engine.
The manufacturer warranty is then invalidated.
Cleaning / replacing the spark plug (g. T + U)
m ATTENTION! Only remove the spark plug when
the engine is cold!
Clean or replace spark plug as required.
Remove the spark plug connector and clean any
dirt from the spark plug areas.
Unscrew the spark plug (8) and check it.
Check the Isolator. If there is any damage, e.g.
cracks or chips, replace the spark plug.
Clean the spark plug electrodes with a wire brush.
Check and set the electrode gap. To make sure
that the engine remains efcient, the spark plug (8)
must have the right electrode gap (0.7-0.8 mm).
Manually screw the spark plug (8) in and tighten it
with the spark plug spanner (g) approximately 1/4
of a revolution.
Tension the belt (k) with the help of the adjusting
screw and ensure that the engine / belt pulley re-
main perpendicular.
Tighten the drive belt (k) if the belt gives more than
10-15 mm (when pressing your thumb on it).
Attach the belt guard (19) again with the two screws.
m ATTENTION!
When removing or installing the drive belt (k), be
careful not to get your ngers caught between the
belt and pulley.
Exciter oil change
The exciter housing is pre-serviced using Automat-
ic Transmission Fluid SAE 10W 30 or its equivalent.
Change uid after 200 hours of operation.
Let exciter cool before changing exciter oil.
Tilt the plate toward a drain pan to aid in the remov-
al of all used oil and particles.
Remove the oil drain screw (m) in order to drain
the oil out of the exciter unit. Check the oil for any
swarf, in order to obtain information to avoid future
problems.
After oil has been completely drained from the ma-
chine, reinstall drain plug (m).
Return plate housing to the upright position.
Remove the plastic cap with the screwdriver.
Fill in the exciter housing with exciter oil through
ller plug (7) opening.
Insert the cover cap.
m ATTENTION!
Do not overll overlling can result in excessive
temperatures in the exciter.
Changing the motor oil (g. R + W)
After 20 operating hours, the oil must be changed for
the rst time, then every 100 operating hours.
To remove the oil proceed as follows:
1. Have an oil collection tray at the ready and then
open the oil drain screw (j).
2. Open the lling cap (measuring stick) (16), tilt the
machine and let the oil drain.
3. Fill the oil (0,6 l) in, check with the measuring stick
(16), and close.
4. Close the oil drain screw (j) again.
5. For storage: Pull starter slowly for 5 times, so that
the oil spreads (without ignition)
Recommended engine oil SAE 10W-30 or 10W-40
(depending on the operating temperature).
Dispose of waste oil according to your country’s reg-
ulations. It is not allowed to drain waste oil onto the
ground or mix it with other waste material.
IM_5904612903_HP2200s_191212_new.indd 30IM_5904612903_HP2200s_191212_new.indd 30 12.12.2019 07:40:2012.12.2019 07:40:20
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HP2200S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HP2200S in de taal/talen: Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 12.1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info