781434
28
Verklein
Vergroot
Pagina terug
1/228
Pagina verder
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
28 | GB
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (27a) must be xed at the
outer position.
Open the locking lever (27b) for the adjustable stop
rail (27a) and push the adjustable stop (27a) rail
outwards.
The adjustable stop rail (27a) must be xed far
enough in front of the innermost position that the
distance between the stop rail (27a) and the saw
blade (5) amounts to a maximum of 8 mm.
Before making a cut, check that the stop rail (27a)
and the saw blade (5) cannot collide.
Secure the locking lever (27b) again.
Move the machine head to its upper position.
Release the rotary table (9) by loosening the set
screw (21).
Using the handle (2), set the rotary table (9) to the
desired angle (refer also to point “Cross cut 90°
and turntable 0° - 45°” in this regard).
Re-tighten the set screw (21) in order to secure
the rotary table.
Undo the locking screw (23)
Use the handle (2) to tilt the machine head to the
left until it coincides with the required angle value
(in this connection see also section Mitre cut 0°-
45°).
Re-tighten the xing screw (23).
Cut as described under section “Cross cut 9
and turntable 0°”.
Saw blade replacement (Fig. 5)
Pull out the mains plug.
Place the saw unit in „cross-cutting“ position
Unlock the moving saw blade guard (6) by pressing
the lock (3 - Fig. 1); in the process, raise the saw
blade guard so that the saw blade is free.
Actuate the spindle lock (22 - Fig. 3).
Loosen the saw blade fastening screw (28) - (At-
tention: left-handed thread).
Remove the screw (28) and saw blade ange (29).
Carefully remove the saw blade (risk of injury from
the saw blade teeth).
Place a new saw blade on the inner saw blade
ange. In the process, observe the rotational di-
rection of the saw blade.
Fit the outer saw blade ange and rmly tighten
the screw.
Move the saw blade guard back to the correct po-
sition.
Replacing laser batteries (Fig. 6)
Remove the laser battery cover (30). Remove the
2 batteries.
Replace both batteries with the same or an equiva-
lent type. Make sure that they are inserted with the
same polarity as the used batteries.
Close the battery cover.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (27a) must be xed in the inner
position.
Open the set screw (27b) on the moveable stop rail
(27a) and push the moveable stop rail (27a) out-
wards.
The moveable stop rail (27a) must be locked in a
position far enough from the inner position that the
distance between the stop rail (27a) and the saw
blade (5) is no more than 8 mm.
Before making the cut, check that no collision could
occur between the stop rail (27a) and the saw blade
(5).
Tighten the set screw (27b) again.
Loosen set screw (21).
Use the handle (2) to set the turntable (9) to the de-
sired angle. The pointer on the turntable must co-
incide with the desired angular extent of the scale
on the base (7).
Re-tighten the locking screw (21) to x the turntable
(9).
Cut as described under section „Cross cut 90° and
turntable 0°“.
Mitre cut 0°- 45° (Fig. 1, 1.3)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (27a) must be xed at the
outer position.
Open the set screw (27b) for the adjustable stop
rail (27a) with an Allen key and push the adjustable
stop rail outwards.
The adjustable stop rail (27a) must be xed far
enough in front of the innermost position that the
distance between the stop rail (27a) and the saw
blade (5) amounts to a maximum of 8 mm.
Before making a cut, check that the stop rail (27a)
and the saw blade (5) cannot collide.
Secure the locking lever (27b) again.
Move the machine head to the top position.
Fix the rotary table (9) in the 0° position.
Loosen the set screw (23) and use the handle (2) to
angle the machine head to the left, until the pointer
(25) indicates the desired angle measurement on
the scale (24).
Re-tighten the xing screw (23).
Cut as described under section „Cross cut 90° and
turntable 0°“.
Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1, 2, 1.3)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 4to the left or - 4to the
right in relation to the stop rail (double mitre cut).
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM80L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM80L in de taal/talen: Alle talen als bijlage per email.

De handleiding is 11.77 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info