781401
30
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
30 | GB
Installation lower support spray-lance & hold-
er spray-nozzle with upper holder spray-lance
(Fig.5)
Attach the holder spray-nozzles (3a) and the upper
holder spray-lance (3) to the frame using the plastic
rivets supplied as shown in gure 5.
Align the front of the holder spray-nozzle (3a) to the
front of the engine.
Fasten the lower support spray-lance (7) using the
phillips head screw and locknut as shown in gure 5.
Mounting of spray-lance (Fig.6)
Place the extension (4) on the spray lance (2) as
shown in gure 6 and secure it by turning the xing
clockwise.
m Caution!
Always tighten xing hand-tight! Too loose con-
nection could lead to loosening of the extension of
the spray-head. Thus leads to injuries.
Installation of high pressure hose (Fig. 7 & 8)
Attach the enclosed high pressure hose (13) to the
spray-lance (2) by turning the xing clockwise as
shown in gure 7.
Attach now the end of the high-pressure hose (13) to
the high-pressure hose connection (18) as shown in
gure 8 by turning the xing clockwise.
m Caution!
Always tighten xing hand-tight! Too loose con-
nection could lead to loosening of the high-pres-
sure hose. Thus leads to injuries.
Connection of water supply (external) to the
pump (Fig. 9)
1. Before connecting the garden hose (NOT sup-
plied) to the water supply connection (19), check
the insert strainer (Y). Clean contaminated insert
strainer, replace damaged insert strainer.
Do not operate the high pressure cleaner if
the insert strainer is damaged.
2. To remove all impurities, allow water to run
through the garden hose (NOT included) for 30
seconds. Shut-off water.
IMPORTANT: DO NOT suck up standing water
for the water supply. Use only cold water (below
38 ° C).
3. Insert the strainer in the quick coupling connector
as shown in gure 9 and connect it manually to
the water supply connection (19) by turning clock-
wise.
4. Connect the garden hose (NOT supplied) to the
water supply connection (19). The hose must not
be longer than 15 m. Pull the hose to check for
tight t.
m Caution!
The length of the free garden hose MUST be at
least 3 m between the inlet of the high pressure
cleaner and a shut-off device, such as a Y-stop
clutch or another suitable shut-off valve.
Fill in engine oil and fuel (Fig. 10)
1. Place the high pressure cleaner on a level sur-
face.
m Caution!
If the motor is turned through or started before ll-
ing with oil, the device could be damaged.
2. Open oil cap with oil dipstick (20) by turning coun-
terclockwise and remove
3. Check the oil level using the markings on the dip-
stick (X) (shown Fig. 10).
4. Fill the system with max. 600 ml 4 stroke engine
oil (SAE 10W30).
5. Check the oil level again as described above.
By loosening (counter-clockwise rotation) of
the oil drain screw (W), too much relled oil or
the complete emptying of the system during oil
change can be controlled.
Important! Place the oil drain pan under the
opening when draining.
6. Put on the oil cap with oil dipstick (20) and close it
by turning clockwise.
Fueling with fuel (Fig.11)
m Warning!
Risk of re and explosion!
Observe safety instructions!
1. Open and remove fuel cap (11) by turning coun-
terclockwise
2. Insert a funnel (V) into the opening of the fuel res-
ervoir (11a).
3. Fill fuel in the fuel reservoir (11a) up to max. 3-4
cm below the upper edge.
4. Put on the fuel cap (11) and close the fuel reser-
voir (11a) by turning it clockwise.
9. Operation
Review the unit’s assembly to conrm you have per-
formed all of the following:
1. Be sure to read and understand the full manual
before using pressure washer
2. Make sure handle (1) is in place and secured.
3. Check that oil has been added to the proper level
in engine crankcase.
4. Add proper fuel to fuel tank (11a).
5. Check for properly attached hose connections
6. Check to make sure that there are no kinks, cuts,
or damage to high pressure hose (13).
7. Provide a proper water supply at an adequate
ow.
8. Make sure unit is in level position.
9. Switch on water supply
m Caution!
DO NOT run the pump without the water supply
connected and turned on.
10. Choose spray nozzle (12) you want to use and in-
sert it into spray-lance extension (4). See “How to
use spray nozzle”.
11. Cold start:
Set choke lever to position “Choke” (Fig.12)
Set the ON / OFF switch (16) to the “I” position
Slowly pull on the starter handle (U) to the notice-
able resistance (Fig.13).
Now move quickly and vigorously until the rst au-
dible ignition occurs.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
Heruntergeladen von manualslib.de Handbücher-Suchmachiene
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HCP2600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HCP2600 in de taal/talen: Duits, Engels, Frans, Italiaans, Pools als bijlage per email.

De handleiding is 12.28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info