758664
17
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
17 І 96
maximum level. This is marked with a red dot on the oil
level window (10) (Fig. 8 pos. 10.1). Do not exceed the
maximum lling quantity. Overlling the equipment may
result in damage. Reinsert the oil sealing plug (9) into
the oil ller opening (9.1).
10.6 Cleaning the intake lter (Fig. 4, 6)
The intake lter prevents dust and dirt being drawn in.
It is essential to clean this lter after at least every 300
hours in service. A clogged intake lter will decrease
the compressors performance dramatically. Open the
thumb screw (A) to the remove the intake lter.
Then pull off the  lter cover (C). Now you can remove
the air lter (E) and the lter housing (D). Carefully tap
out the air lter, lter cover and lter housing. Then blow
out these parts with compressed air (approx. 3 bar) and
reinstall in reverse order.
10.7 Storage
m Important!
Pull out the mains plug and ventilate the equip-
ment and all connected pneumatic tools. Switch
off the compressor and make sure that it is secured
in such a way that it cannot be started up again by
any unauthorized person.
m Important!
Store the compressor only in a dry location which
is not accessible to unauthorized persons. Always
store upright, never tilted!
10.8 Releasing excess pressure
Release the excess pressure by switching off the com-
pressor and using the compressed air which is still left
in the pressure vessel, e.g. with a compressed air tool
running in idle mode or with a blow-out pistol.
11. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in this
packaging can be reused or recycled. The equipment
and its accessories are made of various types of mate-
rial, such as metal and plastic. Defective components
must be disposed of as special waste. Ask your
dealer or your local council.
10.1 Cleaning
Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
We recommend that you clean the equipment imme-
diately after you use it.
Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaningagents or sol-
vents; these may be aggressive to the plastic parts
in the equipment. Ensure that no water can get into
the interior of the equipment.
You must disconnect the hose and any spraying tools
from the compressor before cleaning. Do not clean
the compressor with water, solvents or the like.
10.2 Maintenance work on the pressure vessel/con-
densed water (Fig. 1/2)
m Important!
To ensure a long service life of the pressure vessel
(3), drain off the condensed water by opening the
drain valve (11) each time after using.
Release the vessel pressure rst (see 10.8). Open the
drain screw by turning counter-clockwise (looking at
the screw from the bottom of the compressor) so that
all the condensed water can run out of the pressure
vessel. Then close the drain screw again (turn it clock-
wise). Check the pressure vessel for signs of rust and
damage each time before using. Do not use the com-
pressor with a damaged or rusty pressure vessel. If you
discover any damage, then please contact the customer
service workshop.
10.3 Safety valve (Fig. 3/Pos. 12)
The safety valve (12) has been set for the highest per-
mitted pressure of the pressure vessel. It is prohibited
to adjust the safety valve or remove its seal. Actuate the
safety valve from time to time to ensure that it works
when required. Pull the ring with sufcient force until
you can hear the compressed air being released. Then
release the ring again.
10.4 Checking the oil level at regular intervals (Fig-
ure 8)
Place the compressor on a level and straight surface.
The oil level must be between the MAX and MIN marks
on the oil level window (10).
Oil change: we recommend SAE 15W 40 or equivalent.
The original oil  lling must be changed after 100 hours
in operation; thereafter the oil must be drained and
replaced with new oil after every 500 hours in operation.
10.5 Changing the oil (Figure 8/9)
Switch off the engine and pull the mains plug out of the
socket. After releasing any air pressure you can un-
screw the oil drain plug (10) from the compressor pump.
To prevent the oil from running out in an uncontrolled
manner, hold a small metal chute under the opening
and collect the oil in a vessel. If the oil does not drain
out completely, we recommend tilting the compressor
slightly. When the oil has drained out, re t the oil drain
plug (10).
Dispose of the old oil at a drop-off point for old oil.
To ll in the correct quantity of oil, make sure that the
compressor stands on an even surface. Fill new oil
through the oil ller opening (9.1) until it comes up to the
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HC08 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HC08 in de taal/talen: Duits, Engels, Frans, Italiaans, Deens, Zweeds als bijlage per email.

De handleiding is 5,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info