Handleiding Scheppach DS1200 Primaster (pagina 20 van 36) (Duits, Engels, Frans)

782196

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

• First of all, drill holes into the seating surface and

then insert the screws.

• A foam rubber base for reduction of noise is not

supplied with the saw either. However, we express-

ly recommend that you use such a base to keep

vibration and noise to a minimum. Ideal size 400

x 240 mm.

Changing the saw blades

Warning: Switch off the saw and remove the

mains supply plug before installing saw b!ades

in order to avoid injuries caused by unintentio-

na! activation of the saw. The teeth of the saw

blade must always point downwards.

A. Flat saw-blades Fig. 9

Use the adapter (P) with at saw-blades.

The distance results by the setting gauge (12).

The saw-blade is xed with Allen screws.

A.1 Saw-blade removal, Fig. 1 + 9+ 9.1 + 9.2 + 9.3

+ 9.4

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Slightly press the upper arm (M) down (g. 9.1).

• Then remove the sawblade by pulling it forward out

of the supports and through the access perfora-

tion in the table.

A.2 Inserting the saw-blade, Fig. 1 + 9+ 9.1 + 9.2 +

9.3 + 9.4

• Put the saw-blade with the two adapters into the

lower support, the other end into the upper sup-

port.

• Slightly press the upper arm (M) down (Fig. 9.1)

before hooking it in.

• Tighten the blade with the tightening screw (1) by

rotating it clockwise. Check the tightness of the

blade. Keep on rotating clockwise in order to tight-

en the blade even more.

B. Saw-blade with pins

B.1 Saw blade removal, Fig. 1 + 10 + 10.1 + 10.2

+ 10.3

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Remove the saw-blade from the upper and lower

support by slightly pressing the saw´s upper arm

down (Fig. 10, M).

B 2 Inserting the saw-blade Fig. 1 + 10 + 10.1 +

10.2 + 10.3

• Lead one end of the saw-blade through the per-

foration in the table and insert the saw-blade pins

into the notch. Repeat this procedure at the upper

blade support.

• Before hooking it in, slightly press the saw´s upper

arm down. (Fig 10)

• Check the position of the blade pins at the sup-

ports (Fig 10.1 + 10.2).

7. Installation

Setting the saw bench, Fig. 3

Setting the angle scale

• Release the star button and bring the saw bench

(Fig. 3, A) to a right angle (Fig. 3, B) in relation to

the saw blade.

• Use a 90° angle tc measure the right angle be-

tween the blade and the bench. The saw blade be

90° to the angle.

• Close the star button again when the distance be-

tween the blade and the 90° angle is at a minimum.

The bench should then be at 90° to the saw blade.

• Release the lock screw (Fig. 3, C) and bring the

indicator to the zero position. Fasten the screw.

Please note: the angle scale is a useful piece of

supplementary equip ment, but should not be used

for precision work. Use scrap wood for saw tests,

adjust the bench if neces sary.

Note: The bench should not be on the motor block,

this can cause undesireable noise.

Horizontal saw bench and diagonal cuts, Fig. 3+4

• The saw bench can be positioned into a 450 di-

agonal position or be left in the horizontal position.

• You can read off the approximate slope angle

by using the angle scale located under the work

bench. For more exact adjustment, use scrap wood

for some saw tests; adjust the bench if necessary.

Blade guard assembly and hold-down clamp, Fig.

5+6

• Assemble the workpiece holder (Fig. 5, A) to the

clamp (Fig. 5, B) as shown in the image. This must

be xed rst to the machine with the tommy screw

(Fig. 5, C).

• Secure the blade guard with the screw and nut.

Assembly of dust blower, Fig. 7

Screw the exi-hose into the opening provided and

tighten it hand-tight.

Mounting the saw on a work bench, Fig. 5

• A workbench made from solid wood is betier than

one made of plywood, as interfering vibrations and

noise are more noticeable with plywood.

• The necessary tools and small parts for assem-

bling the saw on a workbench are not supplied

with the saw. However, use equipment of at least

the following size:

1 Saw body

2 Foam rubber base

3 Work bench

4 Flat seal

5 Washer (7 mm)

6 Hexagonal nut (6 mm)

7 Lock nut (6 mm)

8 Hexagon head screws (6 mm)

20 / 36

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scheppach DS1200 Primaster Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info