Handleiding Scheppach DP18VARIO (pagina 21 van 80) (Nederlands, Duits, Engels, Frans, Italiaans, Pools)

781655

Verklein

Vergroot

Pagina terug

1/80

Pagina verder

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

21 І 80

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

• Ensure that the machine can run without interrup-

tion (i.e. remove workpieces, drill bits, etc.).

Use the speed control lever (6) to in nitely adjust the

speed. The set speed is shown on the digital display (8)

in revolutions per minute.

Important! Never let the pillar drill run when the V-belt

cover is open. Always pull power plug before opening

the cover. Never touch the V-belt when it is rotating.

Drill depth stop (Fig. 16)

The drilling spindle has a swivelling scale ring (26) for

setting the drill depth. Only adjust the setting when the

equipment is at a standstill.

• Press the drilling spindle downwards until the tip of

the drill bit touches the workpiece.

• Slacken the clamping screw (25) and turn the scale

ring (26) forwards until it stops.

• Turn the scale ring (26) back to the desired drill depth,

then lock this setting into place using the clamping

screw (25).

Important! When setting the drill depth of a cylindrical

hole you must add the length of the drill tip.

Setting the angle of the drill table (Fig. 1/17)

• Slacken the carriage bolt (27) under the drill table (4).

• Set the drill table (4) to the desired angle..

• Tighten down the carriage bolt (27) in order to lock the

drill table (4) into this position.

Setting the height of the drill table (Fig. 18/19)

• Slacken the tightening screw (3).

• Set the drill table to the desired position with the help

of the hand crank (17).

• Screw the tightening screw (3) back down again.

Drill table and roll base (Fig. 20)

• Slacken the clamping screw (3) to turn the drill table

(4).

• Slacken the thumb screws (21) to extend the roll base

(13).

Clamping the workpiece

As a general rule, use a machine vice or another suita-

ble clamping device to secure a workpiece in position.

Never hold the workpiece in place with your hand! When

drilling, the workpiece should be able to travel on the

drill table (4) for selfcentering purposes. Ensure that

the workpiece cannot rotate. This is best achieved by

placing the workpiece /machine vice on a sturdy block.

Caution! Sheet metal parts must be clamped in to

prevent them from being torn up. Properly set the height

and angle of the drill table for each workpiece. There

must be enough distance between the upper edge of the

workpiece and the tip of the drill bit.

Using the laser (Fig. 21)

To switch on: Move the ON/OFF switch (28) to the

“I” position to switch on the laser. Two laser lines are

projected on the workpiece and intersect at the center of

the drill tip contact point.

To switch off: Move the ON/OFF switch (28) to the “0”

position.

Working light operation (Fig. 21/22)

Note: Always ensure good lighting at the work station

Switching on: Move the on/off switch (29) into the “I”

position to switch the working light (30) on.

Switching off: Move the on/off switch (29) into the “0”

position.

degreased using an environmentally friendly solvent.

This ensures optimal transmission of power.

Installing the machine

Before you use the drill for the rst time it must be

mounted in a stationary position on a rm surface. Use

both mounting holes in the base plate to do this. Ensure

that the machine is freely accessible for operation,

adjustment and maintenance.

Important: The xing screws may only be tightened to a

point where they do not distort or deform the base plate.

Excessive tension can lead to fracture.

Prior to starting

Ensure that the voltage of the mains supply complies

with the specications on the rating plate. Connect the

machine only to a socket with the properly installed

earthing contact. The table drill is equipped with a no-

volt trip that is designed to protect the operator from an

undesired restart following a drop in voltage. Should this

occur, the machine must be manually restarted.

Using the saw

General (Fig.14)

To switch on the machine, push in the green On button

“I” (23); the machine starts up. To switch off , press the

red Off button “O” (24); the device shuts down.

Ensure that you do not overload the device.

If the sound of the motor drops in pitch during operation,

it is being overloaded.

Do not overload the device to the point where the motor

comes to a standstill. Always stand in front of the machi-

ne during operation.

Inserting the tool (Fig. 1)

Make sure that the power plug is removed from the

socket-outlet before changing tools. Only cylindrical

tools with the stipulated maximum shaft diameter may

be clamped in the scroll chuck (12). Only use a tool that

is sharp and free of defects. Do not use tools whose

shaft is damaged or which are deformed or awed in

any other way. Use only accessories and attachments

that are specied in the operating instructions or have

been approved by the manufacturer. If the pillar drill

should become jammed, switch off the machine and

return the drill to its starting position.

Handling the keyless chuck

Your pillar drill is equipped with a keyless chuck. This

enables tools to be changed without the need for an

additional chuck key. To do so, insert the tool in the

quick-change drill chuck and tighten by hand.

Using tools with tapered shanks (Fig. 15)

The pillar drill comes with a spindle taper. To use tools

with tapered shanks (MK2), proceed as follows:

• Move the drill chuck to the lower position.

• Eject the tapered shank using the supplied drill drift

(b), taking care as you do so to ensure that the tool

does not land on the oor.

• Insert the new tool with tapered shank in the spindle

taper with a jolt and then check that the tool is correct-

ly seated.

Setting the speed (Fig. 1)

The operating speed of the machine is in nitely adjusta-

ble.

Important!

• Speed adjustments are allowed only when the

motor is running.

• Slowly and steadily move the speed control lever

(6) while the machine is in idle mode.

Scheppach DP18VARIO Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info