781462
32
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
www.scheppach.com
32 | GB
When cutting thicker wood, special attention must
be paid not to bend or twist the saw blade.
Handling the saw blade properly increases its ser-
vice life.
9.2 On/o󰀨 switch (16)
Switching on: Press the “I” button.
Switching o󰀨: Press the “0” button.
ATTENTION
The machine is equipped with a safety switch against
reactivation if the voltage drops.
If the scroll saw is switched on and the power supply
in the mains is interrupted, the scroll saw remains
switched o󰀨, even if the power supply is re-established.
Press the “I” button to switch it on.
9.3 Work lamp operation (g. 4)
1. Switch the machine on as described in 9.2.
2. The work lamp (20) may not be switched on/and o󰀨
with the work lamp on/o󰀨 switch (21).
9.4 Stroke rate controller (g. 2)
The stroke rate controller (18) allows you to set the
stroke rate according to the material to be cut. In case
of soft material, we recommend high stroke rates, while
strokes rates should be kept low for hard material. Turn
the stroke rate controller (18) clockwise to increase the
stroke rate. Turning anti-clockwise lowers the stroke
rate.
9.5 Operating modes (g. 1, 2)
The scroll saw is able to be operated manually or via
the foot pedal.
9.5.1 Manual controls
1. Ensure that the machine is switched on.
2. Set the operating mode selection switch (17) to the
M” position to operate the saw manually.
8.5 Installing the depressor (g. 6, 7)
NOTE:
Before assembling the depressor (24), the saw blade
pre-installed at the factory (22) must be removed (see
8.1.3).
1. Remove the saw blade (22) as described in 8.1.3.
2. Remove the depressor (24) from the saw blade
guard (5) by loosening the screw (25) completely
(see g. 6).
3. Insert the holder (4) into the opening (see g. 7).
4. Fasten the holder (4) with the knurled screw (3).
5. Install the depressor (24). Insert the screw (25) into
the holder (4) and fasten it.
6. Insert the saw blade (22) again as described in
8.1.3.
7. Ensure that the depressor (24) does not contact
the saw blade (22).
The depressor (24) must always be adjusted accord-
ing to the workpiece height. However, the workpiece
should not be clamped, but should rather be able to
move freely.
The depressor (24) is used to lock the workpiece so
that it cannot swing upwards, which would destroy the
saw blade (22).
8.6 Chip extraction (g. 13)
ATTENTION: Only operate the device with an extrac-
tion system.
Connect a suitable chip extraction system (not included
in the scope of delivery) to the suction connection (15)
(see g. 13, sample gure).
ATTENTION: Check and clean the suction channels at
regular intervals.
9. Operation
9.1 General information
The saw does not cut wood automatically. Rather,
the operator must push and guide the wood toward
the moving saw blade.
The teeth only cut the wood on the downstroke.
The wood must be slowly pushed and guided toward
the saw blade, since the teeth of the blade are very
small.
Those who want to use the saw must go through the
process of learning how to do so. During this time, a
few blades will invariably break.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach DECO-XLS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach DECO-XLS in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info