782495
20
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
18 english
Danger: The laser is activated when the saw blade turns.
Donotlookintothebeam,evenwithopticalinstruments.
Do not remove the warning sign which is attached to the
saw blade cover. Avoid direct eye contact with the light
source.
Note: Theredlaserbeamappearsasadottedlinewhen
the motor is activated and the saw blade Is in the highest
position.Thisdottedlineallowsyoutoadjustthemarkings
on the materials with the cutting line of the saw blade.
Whenthesawbladeisbroughtdownward,theprotection
is removed and the dotted line becomes a continuous laser
beam.
LaserWarningSign:Maximumoutput<1mWDiodenlaser:
630–670nm.CorrespondstothestandardEN608251.
Laser Operation
Withthesawbladeunitinthemostuprightposition:
• Placeyourmaterialsonthemitreboxsaw.
• Switchthesawontoactivatethelaserbeam.
• Makesurethatthelaserbeamandthemarkingsonyour
materialsareinagreement.(Warning: do not lower the
sawbladeduringadjustments.)
• Should the markings on the materials and the laser
beam not agree with each other, switch the machine off,
waituntilthebladehascometoacompletestandstill,
andadjustthepositionofthematerials.
• Switchthesawonandrechecktheline.
• Onceagreementhasbeenreached,fastenthematerials
with a screw vice and carry out the cut.
Changing the Saw Blade (fig. 24, 25, 26)
Warning: In order to prevent an unintentional start up of
the saw, always switch off and unplug the machine be-
fore changing the saw blade. Use correctly sharpened saw
blades. Conform to the maximum speed and the tooth type
indicated on the saw blade. Exchange of saw blades and in-
stallation must be carried out correctly. Only use saw blades
of the type recommended in the operating instructions.
Removal of the Saw Blades
• Unplugthemachinefromthepowersource.
• Raisethemitreboxsawintotheuprightposition.
• Raisethelower,transparent,plasticsawbladecoverinto
themostuprightposition(1,g.24).
• Whileholding onto thelower sawbladecover, release
thescrewofthecover(2,g.24)withaPhillipsscrew-
driver.
• Turnthecover(3)soastorevealtheframescrew(4,
g.26).
• Putthebladekeyontheframescrew.
• Findthecorrugatedclosureandholdthissteadywhile
turning the blade in a clockwise direction. The corrugat-
edclosurewillclickinandadjusttheguard.Continue
to hold the closure while turning the key in a clockwise
direction to release the closure.
• Removethebracingclamp(5,g.26)fromthebracing
cylinder(6)andtheblade(7).Donotremovetheinner
cylinder.
• Liftupthetransparent,plasticsawbladeprotection(1,
g.24)totheuprightpositioninordertoremove the
blade.
Note: Pay closeattentionto thepartswhichyouremove
andthewaytheywereinstalled.Cleananysawdustaway
fromthecylindersbeforeyouinstallanewblade.The254
mmbladehasawaveholewitha16mmreductionpiece
in order to assemble it on the saw.
Installing the Saw Blade
Unplug the machine before changing or installing a saw
blade.
• Installa254mmsawbladewitha16mmwave.Please
notethatthedirectionalarrowwhichpointsinaclock-
wise direction and the upper saw blade must be in
agreementontheblademustcorrespondtoeachother
andthesawbladeteethhavetopointdown.
• Putthebracingcylinder(4,g.26)ontothebladeand
thewave.Screwthebracingcylinder(6)tothewavein
an anticlockwise direction. Important: Make sure that
theatpartofthecylinderandtheatpartofthewave
shaftlockintoeachother.Equally,theatsideofthe
bracing cylinder must meet the blade.
• Placethebladekeyintothewavescrew.
• Pressonthewaveclosure(5,g.25)andholdittightly
while turning the blade in an anticlockwise direction.
Whenitclicksin,pressthewaveclosurefurtherdown
and turn the bracing screw until it is tight.
• Returnthecoveringplates(3,g.24)totheiroriginal
positionuntiltheslitinthecoverisoverthescrew(2,
g.24). While holding on to the lower saw blade lid,
tightenthescrewwithaPhillipsscrewdriver.
Note: Thelower sawblade covermust bein theupright
positioninordertoachieveaccesstothecoveringplate
screw.
• Movethetransparentsawbladeprotectioncover(1,g.
24)downandmakesurethatnowheredoesItmakecon-
tact with the blade.
• Seethatthewaveclosureisreleasedsothattheblade
can turn freely. Turn the blade until the closure is re-
leased.
Note: Bothcylinderpartsmustbecleanandproperlyposi-
tioned. Put the blade down into the lower table and ensure,
by turning it by hand, that it does not come into contact
with the body of the machine or the mounting table.
m Electrical Connections
• Checktheelectricalconnections.Donotusedamaged
cables. See the section on electric cables.
• Onlyanelectricalspecialistshouldundertakeinstalla-
tion,repairsandmaintenanceworkontheelectriccon-
nections.
• To deal with power malfunctions, switch off the ma-
chine.Pullouttheplug.
• Switchoffthemotorwhenyouleavetheworkplace.Pull
outtheplug.
• Even when the machine is only being moved a small
distance,unplugitfromexternalpowersources!Before
operatingthemachineagain,plugthemachineinprop-
erly!
Theelectricmotorinstalledinthemachineisreadytoop-
eratewhenitisdelivered.Theconnectioncorrespondsto
therelevantVDEandDINnorms.Thecustomer‘selectri-
cal connection as well as the extension leads used must
alsocorrespondtothesenormsor,respectively,thelocal
electrical standards.
Defective Electrical Connections
Electricalconnectionscanoftenhaveinsulationdecien-
cies. Possible causes include:
• Pressurepointswhenthecableispassedthroughdoor
or window cracks.
• Bendingpointsduetoinexpertbindingorlayingofelec-
trical cables.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Capas 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Capas 5 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 9.1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info