782113
35
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
8.2
Operating deviations Shaper
Machine vibrates:
- Clamping levers for height and diagonal adjustment are not tightly screwed.
- Sawing tool is not tightly screwed.
Cuts are not clean/wood is burned:
- Sawing tool is dull
- Sawing tool is incorrectly mounted.
Rapid sawing tool wear:
- Sawing tool is incorrectly sharpened.
- Contaminated wood (cement, sand, nails).
Motor becomes too warm:
(It is too hot to touch with bare hands, it continuously shuts itself off.)
- By all means have a qualied electrician inspect the motor.
Machine comes to a stop:
- Overloading (feeding too rapid, sawing tool is dull).
Wood is raised by the rear side of the saw blade:
- Longitudinal limit stops are not parallel
- Splitting wedge is not aligned or crossing is too weak.
The spindle height is difcult to adjust:
- Thoroughly clean and lubricate the threaded rod, gears and slide tracks.
- Check the operation of the clamping lever.
Miscellaneous:
- Bearings make unusual noises: Inspect the bearings and replace if necessary.
- Check the tension of the V-belt (V-belts are accessible when the exhaust cover is removed).
8.1
Operating deviations Saw
Machine vibrates:
- Clamping levers for height and diagonal adjustment are not tightly screwed.
- Sawing tool is not tightly screwed.
Cuts are not clean/wood is burned:
- Sawing tool is dull
- Sawing tool is incorrectly mounted.
Rapid sawing tool wear:
- Sawing tool is incorrectly sharpened.
- Contaminated wood (cement, sand, nails).
Motor becomes too warm:
(It is too hot to touch with bare hands, it continuously shuts itself off.)
- By all means have a qualied electrician inspect the motor.
Machine comes to a stop:
- Overloading (feeding too rapid, sawing tool is dull).
Wood is raised by the rear side of the saw blade:
- Longitudinal limit stops are not parallel
- Splitting wedge is not aligned or crossing is too weak.
The spindle height is difcult to adjust:
- Thoroughly clean and lubricate the threaded rod, gears and slide tracks.
- Check the operation of the clamping lever.
Miscellaneous:
- Bearings make unusual noises: Inspect the bearings and replace if necessary.
- Check the tension of the V-belt (V-belts are accessible when the exhaust cover is removed).
8.0 Malfunctions
GB
8.3 Planer-thicknesser
Operating deviations
If your machine is maintained properly, it is unlikely that any problems will arise.
If the motor will not run:
- check the electrical system is switched on
- check that the machine is connected to the power supply
- drop in voltage (should be checked by a qualified electrician)
- Check the position of the vacuum exhaust sensor
When the machine tables are hard to adjust:
- grease the threaded rods, sliding surfaces, etc.
If the machine runs at an abnormally slow speed:
- the cutters are blunt
- depth of cut too great (adjust according to the hardness and width of the timber, and the condition of the cutters)
- drive rollers are dirty (clean them)
- table not clean or surface in a state of deterioration
- the drive belt is slipping
The machine vibrates:
- cutters are blunt or badly adjusted
- the cutters used are of different sizes (matching set only must be used)
- uneven floor mounting (adjust floor stand accurately)
The machine locks during planing:
- uncouple the drive
- switch off the motor
- remove cutter by lowering the planing table a little way
- reduce depth of cut and begin again, gradually reapproaching the planed depth
If a heel forms or the face is uneven after surfacing:
- the cutter is set higher than the exit table
- the workpiece is running incorrectly on the work tables
- see also “machine vibrates” 35
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach Bestcombi 5.0 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach Bestcombi 5.0 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 6.33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info