Handleiding Scan 5002 (pagina 24 van 32) (Engels)

745582

Verklein

Vergroot

Pagina terug

1/32

Pagina verder

REFUELLING

It is important to obtain as high a temperature as possible in the combustion chamber. This results in best possible use

of the stove and fuel, as well as achieving clean combustion. In this way you will avoid build-up of soot on the combustion

chamber lining and glass pane. During operation, you should not see any smoke; just a movement in the air that indicates

combustion is in progress.

¬ After completing the lighting phase, you should have a good layer of embers in the stove; you can then start

operation of it properly.

¬ Add 2-3 pieces of wood at a time: they should be about 0.5 kg in weight and about 30 cm long.

NOTE: The wood must catch ﬁre quickly. This is why we recommend setting the primary air ﬂow fully open.

NOTE: Operating the stove at too low a temperature and with too little primary air can lead to gases igniting, which

can damage the stove.

¬ When adding wood, always open the glass door carefully to prevent smoke escaping. Never add wood, while

the fire is burning nicely.

WARNING ABOUT OVER-FIRING

If the stove is continiously ﬁred with larger amounts of wood than recommended and/or receives too much air, this can

cause a heavy heat development liable to damage both stove and the surrounding walls. We therefore recommend that

you always observe the max. recommended amount of fuel (See under ”Technical Data”).

USING THE STOVE IN VARIOUS WEATHER CONDITIONS

The way the wind affects the chimney can have a big impact on how your stove reacts under various wind loads; you may

need to adjust the airﬂow to achieve good combustion. Fitting a damper in the ﬂue pipe may also help, as it will allow you

to regulate the draught under changing wind loads. The damper must not close more than 80% of the ﬂue pipe.

Fog and mist can also have a big impact on chimney draught; you may need to use other settings for the combustion air to

achieve good combustion.

GENERAL NOTES

PLEASE NOTE: parts of the built-in stove, especially the outer surfaces, become hot during use. Due care should be exer-

cised Never place ﬂammable material in the radiation zone of the stove!

¬ Never empty ashes into a ﬂammable container. Ashes can contain glowing embers long after you ﬁnish operating the stove.

¬ When the stove is not in use you can close the dampers to avoid a draught through the stove.

¬ If the stove has not been used for some time, check the ﬂue passageways for potential blockages before relighting.

THE FUNCTION OF THE CHIMNEY

The chimney is built-in stove’s motor; its performance determines how well your stove will work. The draught in the

chimney creates negative pressure in the wood-burning stove. The negative pressure draws the smoke out of the stove

and takes in air through the combustion air damper to fuel the combustion process. Combustion air is also used for the

airwash system that keeps the glass clear of soot.

The draught in the chimney is created by the difference in temperature inside and outside the chimney. The higher the

difference in temperature, the better the draught. This is why it is important that the chimney reaches operating tem-

perature before you reduce the damper settings to restrict combustion in the stove (a brickwork chimney will take longer

to reach operating temperature than a steel chimney). It is very important that the operating temperature is reached as

quickly as possible on days when the draught in the chimney is poor due to unfavourable wind and weather conditions.

You need to get a few ﬂames going as quickly as possible. Chop the wood extra thin; use an extra ﬁre lighter etc.

¬ After longer periods without use, you must check the chimney ﬂue for blockages.

¬ You can connect several units to the same chimney. You should however ﬁrst check the relevant regulations in

this respect.

CHIMNEY FIRE

In the event of a chimney ﬁre, keep the stove door, ash drawer, and all dampers on the stove closed. In an emergency, call

the ﬁre service.

¬ We recommend that you get a chimney sweep to check the chimney before using the stove again.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Scan 5002 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Scan 5002

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info