699062
38
Verklein
Vergroot
Pagina terug
1/51
Pagina verder
36 User Manual SATEL
between starting the function to the actual end of the test (during this the FINISH TEST
function will be still available).
12. Depending on the type of tested detector:
magnetic contact open and close the door or window protected by means of the
magnetic contact,
motion detectors pass in front of the detector,
other detectors follow the manufacturer's directions for the detector testing.
13. Look through the test results. To do so, enter again the ZONES TEST submenu (see: steps
1-5) and start the VIEW RESULTS function. You can scroll through the list of results, using
the and keys. Press the or key to switch over the display to the graphic mode,
in which information is provided by means of symbols:
- zone was not violated,
- zone was violated.
Pressing the or key in the graphic mode will display information on another set of
zones (see also description of the
LEDs, p. 7).
The test results can be deleted by means of the CLEAR RESULTS function (TESTS
ZONES TEST CLEAR RESULTS).
5.15 Outputs control
If permitted by the installer, the control function can be started without user
authorization, upon pressing in turn the 8 and keys.
1. Enter the code and confirm with the
key
.
2. Press the 8 key. Depending on how the control panel has been configured by the installer:
a group of outputs will be displayed using the and keys, find the group which
includes an output, and then press the
key to display the list of outputs,
the list of controllable outputs will be displayed at once.
3. Using the and keys, find in the list the output whose status you want to change to
control the device connected to the output. The output status is presented by means of
symbols:
- output inactive (disabled),
- output active (enabled).
The output status can be presented according to the zone status. The displayed
symbols should then be interpreted as follows:
- zone not violated (the device controlled by output is inactive),
- zone violated (the device controlled by output is active).
The way of presenting the status of roller shutter outputs differs from how the status of
other outputs is presented (see: “Controlling the roller shutter outputs”).
5.15.1 Controlling the MONO SWITCH type of output
When the output is inactive:
pressing the key will activate the output for the time programmed by the installer,
pressing the key will allow you to program the time for which the output will be
activated upon the next pressing of the
key.
When the output is active, pressing any digit key will turn the output off.
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel integra 128-WRL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel integra 128-WRL in de taal/talen: Engels als bijlage per email.

De handleiding is 1,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel integra 128-WRL

Satel integra 128-WRL Aanvulling / aanpassing - Nederlands - 121 pagina's

Satel integra 128-WRL Gebruiksaanwijzing - Nederlands - 52 pagina's

Satel integra 128-WRL Snelstart handleiding - Nederlands - 24 pagina's

Satel integra 128-WRL Installatiehandleiding - Nederlands - 2 pagina's

Satel integra 128-WRL Installatiehandleiding - Deutsch - 2 pagina's

Satel integra 128-WRL Aanvulling / aanpassing - Deutsch - 121 pagina's

Satel integra 128-WRL Gebruiksaanwijzing - Deutsch - 38 pagina's

Satel integra 128-WRL Aanvulling / aanpassing - English - 114 pagina's

Satel integra 128-WRL Installatiehandleiding - English - 37 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info