629722
13
Verklein
Vergroot
Pagina terug
1/43
Pagina verder
SATEL VERSA IP 11
6.2 Codes
Operating the alarm system by means of the keypad is possible after entering the code. Only
some functions can be run without the code being entered.
Do not make your code available to other people.
Using an incorrect code three times may:
trigger an alarm,
block the keypad for 90 seconds.
As long as the keypad is blocked, entering the correct code is treated as entering an
incorrect code (“Wrong code” message is displayed).
6.2.1 Factory default codes
By default, the following codes are preprogrammed in the control panel:
user 30 code: 1111
service code: 12345
The factory default codes should be changed before you start using your alarm
system (see: “Change own code”).
6.3 Arming
Completion of the steps below will start the arming procedure. The procedure ends when the
exit delay time elapses (if the countdown is completed successfully, the system becomes
armed – see also “Failure of arming procedure” p. 13). If the exit delay time is 0, the system
becomes armed instantly.
You can change the arming mode, which means you do not have to disarm the system to set
the partition to another arming mode. In the case of alarm, changing the arming mode or re-
activating the same arming mode will result in clearing the alarm (it does not apply to the
quick arming mode).
The day/night arming modes are available if the installer has defined which zones are
to be active in this armed mode.
If exit delay is programmed for a partition, you can leave the partition through the exit
route without triggering alarm after the partition arming procedure has started. The
exception is when the partition is armed without exit delay.
6.3.1 Arming without partition selection
Enter the code, and then press:
- to arm in full mode,
- to arm in day mode,
- to arm in night mode.
The partitions to which you have access will be armed.
6.3.2 Arming with proximity card VERSA-LCDR / VERSA-LCDM-WRL
You can use one of the following methods to arm the system (consult with the installer which
method is to be used):
bring the card close to the keys and move it away,
bring the card close to the keys and hold it there for about 3 seconds.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Satel-Versa-IP

Zoeken resetten

  • Gele LED knippert, gebruikersmenu info systeemstatus (7#) zegt: batterijspanning is laag. Maar systeem (Versa IP) is aangesloten op electriciteitsnet, heeft geen batterij. Ik weet niet hoe ik van dat geknipper af moet komen. Gesteld op 30-7-2022 om 17:52

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel Versa IP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel Versa IP in de taal/talen: Engels als bijlage per email.

De handleiding is 0,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel Versa IP

Satel Versa IP Snelstart handleiding - Nederlands - 2 pagina's

Satel Versa IP Gebruiksaanwijzing - Nederlands - 45 pagina's

Satel Versa IP Snelstart handleiding - Nederlands - 12 pagina's

Satel Versa IP Aanvulling / aanpassing - Nederlands - 93 pagina's

Satel Versa IP Gebruiksaanwijzing - Nederlands - 45 pagina's

Satel Versa IP Snelstart handleiding - Deutsch - 11 pagina's

Satel Versa IP Aanvulling / aanpassing - Deutsch - 97 pagina's

Satel Versa IP Gebruiksaanwijzing - Deutsch - 45 pagina's

Satel Versa IP Installatiehandleiding - Deutsch - 38 pagina's

Satel Versa IP Snelstart handleiding - English - 11 pagina's

Satel Versa IP Gebruiksaanwijzing - English - 32 pagina's

Satel Versa IP Installatiehandleiding - English - 36 pagina's

Satel Versa IP Aanvulling / aanpassing - English - 93 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info