699458
7
Verklein
Vergroot
Pagina terug
1/87
Pagina verder
SATEL VERSA 5
1. Introduction
The VERSA alarm system can be configured by using:
keypad,
computer with DLOADX program installed (locally or remotely).
Local programming (using the keypad or DLOADX program) is possible, if one the following
conditions is met:
PERMANENT ACCESS option is enabled (SERV. ACCESS user function ([code]
0. SERVICE 5. SERV. ACCESS) – see: USER MANUAL) – the option is enabled by default,
access to the control panel has been granted temporarily to the service personnel (ACCESS
TIME
user function ([code] 0. SERVICE 6. ACCESS TIME) – see: USER MANUAL).
As required by the standards, the service access after completion of the installation
has to be limited by the administrators.
2. Configuring the control panel with keypad
The control panel can be programmed using the functions available in the service mode. In
case of the LED keypad, programming is subject to some limitations (e.g. entering names is
impossible). Programming the control panel by use of LED keypad is not recommended
by SATEL.
The service mode is indicated on the keypads by means of the
LED. The LED is lit on
the keypad in which the service function menu is available, while it is blinking on all the other
keypads. The service mode may also be signaled acoustically, after the corresponding option
is enabled. Additional information is provided by the
LED, which is:
blinking during navigation throughout the menu and submenus,
lit when any service function is running.
When in the service mode, the alarm system signals no alarms.
2.1 Starting the service mode
1. Enter the service code (by default: 12345) and press the key.
2. Press in turn . The service mode will be started.
2.2 Starting the service mode “from pins”
When entering the service mode in the normal way is not possible (the control panel does not
support keypads, does not accept the service code, etc.), you can use the emergency
procedure, so-called, starting “from pins”.
1. Power off the control panel (disconnect AC mains first, and the battery next).
2. Place a jumper across the RESET pins.
3. Power up the control panel (first connect the battery and then the AC power).
4. Wait a few seconds and remove the jumper from the RESET pins. The control panel will
enter the service mode. The service mode menu will be available on the keypad with the
lowest address (in the case of the wireless keypad, the menu will be displayed after
pressing any key).
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel VERSA 15 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel VERSA 15 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel VERSA 15

Satel VERSA 15 Snelstart handleiding - Nederlands - 11 pagina's

Satel VERSA 15 Gebruiksaanwijzing - Nederlands - 44 pagina's

Satel VERSA 15 Snelstart handleiding - Nederlands - 2 pagina's

Satel VERSA 15 Aanvulling / aanpassing - Nederlands - 86 pagina's

Satel VERSA 15 Installatiehandleiding - Nederlands - 35 pagina's

Satel VERSA 15 Snelstart handleiding - Nederlands - 2 pagina's

Satel VERSA 15 Aanvulling / aanpassing - Deutsch - 11 pagina's

Satel VERSA 15 Gebruiksaanwijzing - Deutsch - 44 pagina's

Satel VERSA 15 Installatiehandleiding - Deutsch - 37 pagina's

Satel VERSA 15 Snelstart handleiding - Deutsch - 2 pagina's

Satel VERSA 15 Snelstart handleiding - English - 11 pagina's

Satel VERSA 15 Installatiehandleiding - English - 36 pagina's

Satel VERSA 15 Gebruiksaanwijzing - English - 32 pagina's

Satel VERSA 15 Gebruiksaanwijzing - English - 42 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info