699537
19
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
SATEL PERFECTA LTE 17
6.10.1 Programming the address by means of the service function
The address programming function can be started from either a wired or wireless
keypad, but it will only allow setting addresses in the wired keypads.
1. Start the service mode (see: “Starting the service mode” p. 15).
2. Press successively to run the 20.K
PD
.
ADDRESS
function.
3. Information on the current address and permissible address range will be displayed on all
wired keypads (see Fig. 14).
Fig. 14. Programming keypad address (n = current address).
4. On the keypad the address of which you want to change, press the key whose digit
corresponds to the new address.
5. Press
to finish the function (the function will be finished automatically after 2 minutes
since it was launched). The keypad will be restarted.
6.10.2 Programming the address without entering the service mode
This way of address programming is useful when the keypad operation is blocked and
starting the service mode is impossible.
1. Power off the keypad.
2. Disconnect wires from the keypad CLK and DTA terminals.
3. Short the CLK and DTA keypad terminals.
4. Power on the keypad.
5. Information on the current address and permissible address range will be displayed on
the keypad (see Fig. 14).
6.
Press the key whose digit corresponds to the new address (if you make a mistake, press
to restart the keypad – current address information will be displayed again).
7. Power off the keypad.
8. Open the CLK and DTA keypad terminals.
9. Connect wires properly to the CLK and DTA keypad terminals.
10. Power on the keypad.
6.11 Identification of devices connected to the bus
Devices connected to the communication bus will not be properly supported, unless they
have been identified by the control panel. Identification of the devices is required after the
first start-up of the control panel and then each time after a new device is added or the
address was changed in a device supported by the control panel.
Disconnecting an identified device from the communication bus will trigger the tamper
alarm.
6.11.1 Starting the identification function from keypad
1. Start the service mode (see: “Starting the service mode” p. 15).
2. Press successively
to run the 21.I
DENTIFICAT
. function.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel PERFECTA 32 LTE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel PERFECTA 32 LTE in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel PERFECTA 32 LTE

Satel PERFECTA 32 LTE Gebruiksaanwijzing - Deutsch - 11 pagina's

Satel PERFECTA 32 LTE Aanvulling / aanpassing - Deutsch - 50 pagina's

Satel PERFECTA 32 LTE Installatiehandleiding - Deutsch - 27 pagina's

Satel PERFECTA 32 LTE Snelstart handleiding - English - 10 pagina's

Satel PERFECTA 32 LTE Gebruiksaanwijzing - English - 30 pagina's

Satel PERFECTA 32 LTE Aanvulling / aanpassing - English - 47 pagina's

Satel PERFECTA 32 LTE Aanvulling / aanpassing - English - 50 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info