699465
19
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
SATEL PERFECTA 17
4. When the cursor shows the S
ERVICE MODE
function, press .
5. Service mode menu will be displayed (the cursor will show the E
ND
SM function).
6.9.5 Emergency procedure of the control panel start-up
If the control panel fails to start properly, keypads are not supported, codes are not accepted
by the control panel etc., despite all connections having been made correctly, follow the steps
below:
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery).
2. Put a jumper on the RESET pins.
3. Turn on the control panel power supply (first connect the battery and then the AC power).
4. Wait a few seconds (until LEDs next to the RESET pins stop blinking) and remove the
jumper from the RESET pins. The control panel will enter the service mode. The service
mode menu will be displayed on the wired keypad with the lowest address.
If there is no wired keypad in the alarm system or there is no communication with the
wired keypads (e.g. when the communication bus is shorted), you can get access to
the service mode menu from the wireless keypad with the lowest address. Press any
key on this keypad within 30 seconds of removing jumper from the RESET pins.
The service mode menu will not be displayed, if the D
ISABLE
S
ERVICE
M
ODE
option is
enabled in the control panel. The “Factory settings ? 1=Yes” message will be
displayed on the keypad with the lowest address. You can press to restore the
factory default settings. The service mode menu will not be displayed until the factory
settings are restored.
6.9.6 First steps after starting-up the control panel
Control panel with wired keypads
If wired keypads are connected to the control panel, then, after starting the control panel with
factory settings:
1. Set correct, individual addresses in the wired keypads.
2. Run the function of identification of devices connected to the communication bus of the
control panel.
Control panel without wired keypads PERFECTA 16-WRL / PERFECTA 32-WRL
If no wired keypads are connected to the control panel, then, after starting the control panel
with factory settings:
1. Connect computer to alarm control panel.
2. Use the PERFECTA
S
OFT
program to add wireless keypads.
3. Run the function of identification of devices connected to the communication bus of the
control panel.
6.10 Programming addresses for the hardwired keypads
An individual address from the 0 to 3 range must be set for each keypad. By default, address
0 is preset for all wired keypads. After starting the alarm control panel with factory default
settings, all keypads connected to the bus are supported, no matter what their addresses are.
This allows you to program individual address for the keypads.
Remember to program an individual address if a new keypad is connected to the
already functioning alarm system.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel PERFECTA 16-WRL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel PERFECTA 16-WRL in de taal/talen: Engels als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel PERFECTA 16-WRL

Satel PERFECTA 16-WRL Snelstart handleiding - Nederlands - 11 pagina's

Satel PERFECTA 16-WRL Gebruiksaanwijzing - Nederlands - 32 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - Nederlands - 52 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - Nederlands - 50 pagina's

Satel PERFECTA 16-WRL Installatiehandleiding - Nederlands - 28 pagina's

Satel PERFECTA 16-WRL Snelstart handleiding - Deutsch - 11 pagina's

Satel PERFECTA 16-WRL Gebruiksaanwijzing - Deutsch - 32 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - Deutsch - 52 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - Deutsch - 50 pagina's

Satel PERFECTA 16-WRL Installatiehandleiding - Deutsch - 28 pagina's

Satel PERFECTA 16-WRL Snelstart handleiding - English - 10 pagina's

Satel PERFECTA 16-WRL Gebruiksaanwijzing - English - 31 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - English - 49 pagina's

Satel PERFECTA 16-WRL Aanvulling / aanpassing - English - 50 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info