699075
18
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
16 Installer Manual SATEL
5.5.1 Addressing devices connected to the keypad bus
Each device to be connected to the keypad bus must have its own individual address from
the 0 to 3 (INTEGRA 24 and INTEGRA 32) or from the 0 to 7 (INTEGRA 64
and INTEGRA 128) range. Addresses must not repeat (the control panel does not support
devices having identical addresses). It is recommended that consecutive addresses be
assigned starting from 0.
In keypads, the address is set by software means. By default, address 0 is set. When started
with factory default settings, the control panel will support all keypads connected to the bus,
irrespective of what addresses are set in them. Thus it is possible to set correct individual
addresses in the keypads and perform identification of all devices connected to the bus.
In other devices to be connected to the keypad bus, the address is to be set using the
DIP-switches or the pins.
Programming keypad address by means of the service function
1. Enter the service code (by default 12345) and press the key.
2. Using the or keys, find the SERVICE MODE item in the function list and press the
or key.
3. Start the KEYPADS ADDR. function (STRUCTURE HARDWARE IDENTIFICATION
KEYPADS ADDR.).
4. The message shown in Fig. 6 will appear on display of all keypads connected to the
control panel.
5. Enter a proper address in the selected keypad(s). The address change will be
confirmed by four short beeps followed by one long beep.
Fig. 6. Programming the keypad address with the service function.
6. To terminate the address change function, press the
key. The function will be
terminated automatically after 2 minutes from being started. Termination of the
function is equivalent to restarting the keypad (the service mode menu will be
displayed on the keypad with the lowest address).
Programming keypad address without entering the service mode
This method of address programming is particularly useful when due to repeating
addresses the keypad support has been disabled and entering the service mode is
impossible.
1. Disconnect the keypad power supply (KPD) and the CKM and DTM signal wires.
2. Short-circuit the keypad CKM and DTM terminals.
3. Switch on keypad power supply.
4. A message indicating the current address will appear on the display.
5. Enter a new address. The keypad will confirm execution of the function by four short
beeps followed by one long beep. If it is necessary to change the entered address,
press the key (keypad restart will follow and a corresponding message will appear
on the display).
6. Disconnect the keypad power supply.
7. Open the keypad CKM and DTM terminals.
n=0...7, currently set keypad
address
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel Integra 64 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel Integra 64 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel Integra 64

Satel Integra 64 Gebruiksaanwijzing - Nederlands - 52 pagina's

Satel Integra 64 Snelstart handleiding - Nederlands - 24 pagina's

Satel Integra 64 Aanvulling / aanpassing - Nederlands - 121 pagina's

Satel Integra 64 Installatiehandleiding - Nederlands - 35 pagina's

Satel Integra 64 Aanvulling / aanpassing - Deutsch - 121 pagina's

Satel Integra 64 Gebruiksaanwijzing - Deutsch - 54 pagina's

Satel Integra 64 Installatiehandleiding - Deutsch - 38 pagina's

Satel Integra 64 Snelstart handleiding - Deutsch - 2 pagina's

Satel Integra 64 Gebruiksaanwijzing - English - 51 pagina's

Satel Integra 64 Aanvulling / aanpassing - English - 114 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info