699074
25
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
SATEL INTEGRA Plus 23
2. Identification by the control panel of devices connected to the keypad bus. The
identification can be performed by means of:
the keypad ([SERVICE CODE] SERVICE MODE STRUCTURE HARDWARE
IDENTIFICATION LCD KEYPADS ID.),
DLOADX program (Structure window Hardware tab Keypads branch
Keypads identificationbutton).
3. Identification by the control panel of devices connected to the expander bus. The
identification can be performed by means of:
the keypad ([SERVICE CODE] SERVICE MODE STRUCTURE HARDWARE
IDENTIFICATION EXPANDERS ID.),
DLOADX program (Structurewindow Hardwaretab Expansion modulesbranch
Exp. modules identification button).
The identification function must be run every time when a new device is connected to
the bus or the address of a device connected to the bus is changed.
Disconnecting the identified device from the communication bus will trigger a tamper
alarm.
Any attempt to replace the identified device with another one having the same address
will trigger a tamper alarm.
5.12 Emergency procedure of the control panel start-up
If the control panel fails to start properly, keypads are not supported, codes are not accepted
by the control panel etc., despite all connections having been made correctly, follow the steps
below:
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery).
2. Put a jumper on the RESET pins located on the control panel mainboard.
3. Turn on the control panel power supply (first connect the battery and then the AC power).
The DIALER LED will start blinking.
4. Wait a few seconds until the DIALER LED goes out and remove the jumper from the pins.
The control panel will enter the service mode. The service mode menu will be displayed
on the keypad with the lowest address.
If a computer with the DLOADX program running is connected to the RS-232 port, the
service mode will not start (it will be possible to program the control panel locally from
the computer).
5. Restore the factory default settings using the CLEAR ALL function (RESTARTS CLEAR
ALL
).
6. Start the KEYPADS ADDR. function (STRUCTURE HARDWARE IDENTIFICATION KEYPADS
ADDR
.) and set individual addresses in the keypads (see p. 15).
7. Identify devices connected to the keypad bus (STRUCTURE HARDWARE
IDENTIFICATION LCD KEYPADS ID.).
8. Identify devices connected to the expander bus (STRUCTURE HARDWARE
IDENTIFICATION EXPANDERS ID.).
9. Exit the service mode using the END SERVICE function.
10. After a prompt appears on the keypad display whether to save the data to the FLASH
memory, press the key with the number 1. By saving a copy of the settings to the FLASH
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel Integra 64 Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel Integra 64 Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 0,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel Integra 64 Plus

Satel Integra 64 Plus Gebruiksaanwijzing - Nederlands - 53 pagina's

Satel Integra 64 Plus Aanvulling / aanpassing - Nederlands - 108 pagina's

Satel Integra 64 Plus Installatiehandleiding - Nederlands - 35 pagina's

Satel Integra 64 Plus Gebruiksaanwijzing - Deutsch - 55 pagina's

Satel Integra 64 Plus Aanvulling / aanpassing - Deutsch - 108 pagina's

Satel Integra 64 Plus Installatiehandleiding - Deutsch - 36 pagina's

Satel Integra 64 Plus Gebruiksaanwijzing - English - 51 pagina's

Satel Integra 64 Plus Aanvulling / aanpassing - English - 102 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info