699031
50
Verklein
Vergroot
Pagina terug
1/102
Pagina verder
48 Programming SATEL
in the DLOADX program connected to the control panel, in the Structure window,
Systemtab, after clicking on the partition name and then on the Partition timerbutton.
4.3 Zones
The zone is a separated portion of the protected area which can be supervised by a detector
or detectors. A zone can only be assigned to one partition.
The system supports the following zones:
hardwired on the control panel electronics board, in keypads and expanders.
The number of available hardwired zones is determined by the control panel during
identification procedure.
wirelesswhen the ABAX 2 / ABAX wireless system controller is connected. The number
of available wireless zones depends on the number of wireless devices registered in the
system and is determined during the procedure of adding the devices.
virtual zones which physically do not exist, but have been programmed as FOLLOW
OUTPUT
or are controlled by means of a keyfob.
4.3.1 Assigning zones to a partition
The zones can be assigned to a partition:
using the keypad, in the service mode, by means of the ZONES function (STRUCTURE
SYSTEM PARTITIONS SETTINGS [Part. Name] ZONES) see: Selection from the
multiple-choice listp. 25,
using the DLOADX program:
1. in the Structurewindow, Systemtab, after clicking on the partition name. Click on
the Add button to display the list of zones which can be assigned to the selected
partition. Click on the zone which is to be assigned to the partition.
2. in the Zoneswindow, Zonestab, Part.column, enter the number of partition to
which the given zone is to be assigned.
4.3.2 Programming the EOL resistor values
As regards the zones on the control panel mainboard, in some keypads and expanders, the
value of end-of-line resistors is programmable within the range from 500 to 15 k (the sum
of preset values may not exceed 15 k).
The value of EOL resistors for the zones on mainboard can be programmed:
using the keypad, in the service mode, by means of EOL R1 RESISTOR, EOL R2 RESISTOR
and EOL R3 RESISTOR functions (STRUCTURE HARDWARE EOL R1 RESISTOR / EOL
R2 RESISTOR / EOL R3 RESISTOR),
using the DLOADX program, in the Structurewindow, Hardwaretab, after clicking on
the control panel mainboard.
The value of EOL resistors programmed for the mainboard zones applies also to the
zones in the keypads:
INT-KLCD and INT-KLCDR with electronics version 3.2 and firmware version 2.11
(or later),
INT-KLFR,
INT-KSG with firmware version 1.02 (or later),
INT-TSG,
INT-TSH,
INT-TSI.
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel Integra 256 Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel Integra 256 Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 1,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel Integra 256 Plus

Satel Integra 256 Plus Snelstart handleiding - Nederlands - 2 pagina's

Satel Integra 256 Plus Aanvulling / aanpassing - Nederlands - 108 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - Nederlands - 53 pagina's

Satel Integra 256 Plus Installatiehandleiding - Nederlands - 35 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - Deutsch - 55 pagina's

Satel Integra 256 Plus Aanvulling / aanpassing - Deutsch - 108 pagina's

Satel Integra 256 Plus Installatiehandleiding - Deutsch - 36 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - English - 51 pagina's

Satel Integra 256 Plus Installatiehandleiding - English - 35 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info