699031
24
Verklein
Vergroot
Pagina terug
1/35
Pagina verder
22 Installer Manual SATEL
5.10.2 Backup power supply
A 12 V lead-acid sealed battery should be connected to the control panel as a backup power
source. The battery capacity must be adequately selected to match current consumption in
the system. According to EN 50131 Grade 3, the battery must ensure operation of the system
without mains supply for 30 hours, when the reporting is enabled in the control panel.
Do not connect deeply discharged battery to the control panel (with voltage
across unloaded terminals below 11 V). The battery should be precharged with
a proper charger.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
If the battery voltage drops below 11 V for longer than 12 minutes (3 battery tests), the
control panel will indicate battery failure. When the voltage goes down to approx. 10.5 V, the
battery will be disconnected.
5.10.3 Control panel power-up / start-up procedure
1. Deenergize the 230 V AC circuit to which the transformer is to be connected.
2. Connect the 230 V AC wires to the terminals of transformer primary winding.
3. Connect the terminals of transformer secondary winding to the AC terminals on control
panel electronics board.
4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative
terminal to BLACK lead). The control panel will not start after connecting the battery
alone. Included in the control panel set are adapters (matching connectors) for
connection of battery with twisted cable ends, therefore the battery cable ends should not
be cut off.
5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.
The control panel will start operating.
If you have any problems with starting the control panel, enter the service mode
from the pins and restore the factory default settings (see EMERGENCY
PROCEDURE OF THE CONTROL PANEL START-UP p. 23).
The above mentioned power-up sequence (first the battery, then the 230 V AC mains) will
ensure proper operation of the power supply unit and the electronic protection circuits, thus
preventing damage to the alarm system components caused by installation mistakes, if any.
If the control panel power supply has to be disconnected, disconnect the mains first
and then the battery. When reconnecting the power supply, observe the above
mentioned sequence.
5.11 First start-up of the control panel
After the first start-up of the control panel, it is advisable to restore the factory
default settings using the CLEAR ALL function ([SERVICE CODE] SERVICE MODE
RESTARTS CLEAR ALL), and then quit the service mode. When a prompt
appears on the keypad display, whether the data should be saved to the FLASH
memory, press the “1” key on the keypad.
The control panel with factory settings (a new one or one after restart of settings) supports all
keypads connected to the bus, irrespective of the addresses set in them. However, it does
not allow you to program the system. You will be able to start programming after carrying out
the following operations:
1. Setting individual, correct addresses in keypads (see p. 14).
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel Integra 256 Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel Integra 256 Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 0,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel Integra 256 Plus

Satel Integra 256 Plus Snelstart handleiding - Nederlands - 2 pagina's

Satel Integra 256 Plus Aanvulling / aanpassing - Nederlands - 108 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - Nederlands - 53 pagina's

Satel Integra 256 Plus Installatiehandleiding - Nederlands - 35 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - Deutsch - 55 pagina's

Satel Integra 256 Plus Aanvulling / aanpassing - Deutsch - 108 pagina's

Satel Integra 256 Plus Installatiehandleiding - Deutsch - 36 pagina's

Satel Integra 256 Plus Gebruiksaanwijzing - English - 51 pagina's

Satel Integra 256 Plus Aanvulling / aanpassing - English - 102 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info