699391
10
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
8 INT-TSI SATEL
6.2.2 Programming address without entering the service mode
This method is useful when due to repeating addresses the keypad support has been
disabled and entering the service mode is impossible.
1. Turn off keypad power supply.
2. Disconnect wires from the keypad CKM and DTM terminals.
3. Short the keypad CKM and DTM terminals.
4. Turn on keypad power supply. A window will be displayed where you can set the address.
5. Using the and keys, set the address and then tap the icon.
6. Turn off keypad power supply.
7. Open the keypad CKM and DTM terminals.
8. Connect wires, as required, to the keypad CKM and DTM terminals.
9. Turn on keypad power supply.
6.3 Keypad identification
The alarm system can only be programmed and operated from keypads that have been
identified by the control panel. The keypad identification function should be executed at the
first start-up of the control panel, and then each time when adding a new keypad or changing
address in a keypad supported by the control panel. Disconnecting an identified keypad from
the bus will trigger the tamper alarm.
The identification function can be run by using:
the keypad (SERVICE MODE STRUCTURE HARDWARE IDENTIFICATION LCD KEYPADS
ID
.);
DLOADX program (Structure” window Hardware” tab Keypads” item Keypads
identification” button).
The procedure of entering the service mode by means of the INT-TSI keypad is described in
section Programming keypad address by means of service function” (p. 7).
7. Installation of the keypad working in SLAVE mode
7.1 Installation and hook-up
Follow the procedure set forth in section describing installation and hookup of the keypad
working in MASTER mode (p. 4), but skip the steps 8 and 9 (connecting to the keypad bus of
the control panel and connecting detectors to the keypad zones).
7.2 Activating the SLAVE operating mode
1. Turn off keypad power supply.
2. Short the keypad CKM and DTM terminals.
3. Turn on keypad power supply. The Keypad configurationwindow will be displayed.
4. Tap Network” item. The network settings will be displayed.
5. Select the Slaveoption (see Fig. 6).
6. Indicate the keypad working in MASTER mode by means of which communication with
the control panel is to take place. You can do this in two ways:
tap IP address of the master keypadand use the keyboard that will be displayed to
enter the IP address of that keypad,
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel INT-TSI-WSW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel INT-TSI-WSW in de taal/talen: Engels als bijlage per email.

De handleiding is 2,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel INT-TSI-WSW

Satel INT-TSI-WSW Gebruiksaanwijzing - Nederlands - 20 pagina's

Satel INT-TSI-WSW Installatiehandleiding - Nederlands - 33 pagina's

Satel INT-TSI-WSW Installatiehandleiding - Deutsch - 34 pagina's

Satel INT-TSI-WSW Gebruiksaanwijzing - English - 20 pagina's

Satel INT-TSI-WSW Gebruiksaanwijzing - English - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info