699393
21
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
SATEL INT-TSG 19
zone status by means of messages (select individual zones whose status will be
displayed, and define the content and color of messages for normal state and for
violation, because only these two states are presented in the form of message),
output status by means of messages (select individual outputs whose status will be
displayed, and define the content and color of messages for active and inactive output).
There are three font sizes available for use on the status screen. You can also define color of
the font to be used. Using the “drag and drop” method, you can easily select the place where
the given information will be presented on the display.
Slide show
The keypad can display a slide show (as the status screen background and after 10 minutes
of the keypad inactivity). The photos to be displayed should be stored on a microSD memory.
Their size should not exceed 480 x 272 pixels. Only images in BMP format are supported.
The C
HANGE PICTURE EVERY
parameter defines how fast the images will be changed during
the slide show. If the time equal to 0 is programmed, no slide show will be displayed. If this is
the case, the first picture stored on the microSD card will be displayed as the status screen
wallpaper.
7.1.6 End-of-line resistance
The resistance data are stored in the keypad. Before you start programming the
resistor values, click on the “Read” button in the “EOL resistance value” tab to read the
data from the keypad. Having programmed the resistor values, click on the “Write”
button in the “EOL resistance value” tab to write the data to the keypad. The EOL
resistors related data are not read / written when you click on the button in the
main menu of D
LOAD
X program.
2EOL/NC
ZCOM
R1
R2
A
T
3EOL/NC
ZCOM
R1
R2
A
T
R3
M
Fig. 9. Numbering of EOL resistors (same for the NO detector).
T – tamper. A – alarm. M – masking.
The value of EOL resistors is programmable. Depending on the control panel to whic
h the
keypad is connected:
INTEGRA
: parameters of the EOL resistors should be defined for zones in a single keypad.
Value of the resistors R1 and R2 is to be programmed (numbering of the resistors is
shown in Fig 9). You can enter values from 500
to 15 k
. The total resistance (R1+R2)
may not exceed 15 k
. For the R2 resistor, you can program value 0. In such a case, the
value of resistors used in the Double EOL configuration must be equal to half the value
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel INT-TSG-BSB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel INT-TSG-BSB in de taal/talen: Engels als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel INT-TSG-BSB

Satel INT-TSG-BSB Snelstart handleiding - Nederlands - 2 pagina's

Satel INT-TSG-BSB Gebruiksaanwijzing - Nederlands - 18 pagina's

Satel INT-TSG-BSB Gebruiksaanwijzing - Nederlands - 20 pagina's

Satel INT-TSG-BSB Installatiehandleiding - Nederlands - 28 pagina's

Satel INT-TSG-BSB Snelstart handleiding - Deutsch - 2 pagina's

Satel INT-TSG-BSB Gebruiksaanwijzing - Deutsch - 19 pagina's

Satel INT-TSG-BSB Installatiehandleiding - Deutsch - 29 pagina's

Satel INT-TSG-BSB Snelstart handleiding - English - 2 pagina's

Satel INT-TSG-BSB Gebruiksaanwijzing - English - 20 pagina's

Satel INT-TSG-BSB Gebruiksaanwijzing - English - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info