699577
59
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
SATEL CA-10 57
Restoring default settings, restoring codes
Restoration of settings on entering the service mode by means of service
code
If it is necessary to restore the default settings, you should enter the service mode and call the
service functions FS107 (to restore all the default settings, except for the user access codes)
and FS110 (to restore the partition master default codes, the other codes being erased). Also,
the function FS108 can be performed (in order to erase the event log contents).
Restoration of settings on entering the service mode by hardware means
If the service mode is inaccessible (for example, when the control panel stopped responding to
keypad commands because of a programming error, or the service code has been lost), to
restore default settings follow the procedure below:
1. Disconnect in turn the mains supply and the emergency supply.
2. Set a jumper on J19 RESET pins.
3. Connect in turn the emergency supply and the mains supply.
4. On hearing a beep in the keypad, remove the jumper from J19 pins (the 1
st
partition keypad will enter the service mode).
5. Perform function FS107 (restoring of default settings).
6. Perform function FS110 (restoring of default codes).
7. Exit the service mode or proceed with programming the control panel.
This procedure can be disabled by software means (see: FS131 first option in the first set of
option).
Note: Similarly as in other SATEL control panels, shorting the pins and powering up alone will
not restore any parameters. However, it will activate the service mode thus making it
possible to check how the control panel has been programmed, and to analyze any
programming errors.
Restoration of settings when the option to enter the service mode by
hardware means is locked and it is impossible to use the service code
If the option to enter the service mode by jumper setting is disabled (FS131 first option in the
first set of option) and the panel does not recognize the service code, proceed as follows:
1. Disconnect in turn the mains supply and the emergency supply.
2. Set a jumper on J19 RESET pins.
3. Connect in turn the emergency supply and the mains supply.
4. Wait about 60 seconds (±5 sec.) and remove the jumper.
5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15
seconds) and confirm by pressing the [#] or [
*
] key.
After these operations, the control panel should return to its default settings and remain in the
service mode.
59

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-10

Satel CA-10 Gebruiksaanwijzing - Nederlands - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 4 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 64 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 26 pagina's

Satel CA-10 Installatiehandleiding - Deutsch - 44 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Aanvulling / aanpassing - English - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 24 pagina's

Satel CA-10 Snelstart handleiding - English - 11 pagina's

Satel CA-10 Installatiehandleiding - English - 43 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info