699577
29
Verklein
Vergroot
Pagina terug
1/43
Pagina verder
CA-10 Installer Manual 27
If the control panel operates with one keypad, having a default address (1001 jumpers on
pins „A” and „D”), then, after the power is switched on, the keypad will report readiness for
work with four short beeps followed by a long one.
Note: The control panel with default settings will not support a keypad connected to the
CLK1 signal if the default address (1001) has been changed in that keypad.
If the control panel is alarming after power-up, clear the alarm by means of the user access
code (default master code for partition 1: [1][2][3][4]) and proceed to programming
parameters in the service mode.
Upon entering the default service code [1][2][3][4][5] and confirming it with the [#] key, the
control panel will enter the service mode. The
[ALARM] and [ARMED] LEDs will be
blinking alternately. Now, you can proceed to programming the control panel.
Note: For the safety reasons it is recommended that the keypad default address be
changed. Having done the changes, you must run the FS124 function.
If the system includes more keypads or where the zone expander is installed, the control
panel will not support any devices connected to the signals CLK2, CLK3, CLK4 until their
addresses have been programmed in the control panel memory.
Hardware access to the service mode
If the panel does not „see” the keypad when the power is on, and does not respond to the
keystrokes (access code entry), or keeps on alarming, it is necessary to carry out the
procedure of hardware access to the service mode. This allow to program of the
keypad/expander addresses before the normal operating mode is restored. In the other case,
the control panel will start alarming right after the power-up because it has detected the
keypad tampering.
To start the service mode by means of jumpers follow the procedure below:
1. Disconnect in turn the mains supply and the emergency supply.
2. Check the keypad address jumpers and tamper contacts for correct settings.
3. Put a jumper on the control panel RESET pins (J19).
4. Connect in turn the emergency supply and the mains supply.
5. After the keypad beep, remove the jumper from the RESET pins (J19). The operation
will activate the service mode in partition 1 keypad. This will be signaled by the
keypads with four short and one long beeps.
6. Call the service function FS124. The function automatically reads the keypad address and
prepares the control panel for work in a new configuration.
Note: If LCD keypads are installed in the alarm system, call the FS-124 service function
in each LCD keypad. When activated from the LCD keypad, this function automatically
performs additional configuring operations and its activation in each LCD keypad is
necessary for proper operation of the system.
7. To make sure that all the settings are in accordance with the default values, you can
perform the service functions FS107, FS108 and FS110.
Having completed the procedure, exit the service mode using the function FS0 and activate
the service mode again this time from the keypad by entering the default access code
[1][2][3][4][5] confirmed with the [#] key.
If the control panel has re-entered the service mode, it means that its functioning is correct
and that you may proceed with further installation of the system (connection of sensors,
sirens, establishing communication with a computer, if required) and programming of all
necessary parameters.
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Satel CA-10

Satel CA-10 Gebruiksaanwijzing - Nederlands - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 4 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 64 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 26 pagina's

Satel CA-10 Installatiehandleiding - Deutsch - 44 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Aanvulling / aanpassing - English - 60 pagina's

Satel CA-10 Aanvulling / aanpassing - English - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 24 pagina's

Satel CA-10 Snelstart handleiding - English - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info