699577
9
Verklein
Vergroot
Pagina terug
1/43
Pagina verder
CA-10 Installer Manual 7
33 arm/disarm/clear alarm the output signals the performance of particular operations with,
respectively, one, two, or four pulses 0.16s each.
34 keypad buzzer alarm silent alarm signaling in the partition keypad.
35 power supply on armed mode it functions similarly to the arm status output, but goes on right
after starting the exit delay countdown, not after changeover from the exit delay to the armed mode
(it can be used, for example, as indicator or power supply output for microwave detectors in spaces
where people stay).
36 LED status the output can control a LED to indicate the following statuses:
- off – control panel disarmed
- steady light – control panel armed
- blinking light – the control panel armed, there was alarm or trouble
Note: If in the armed mode any zones are violated in the system, the LED will be blinking
and will only change to steady light after the violation ends.
.37 – RELAY status the output can control a relay. The output becomes active after arming, and inactive
after an alarm is triggered, a trouble occurs, or the system is disarmed.
Note: If in the armed mode any zones are violated in the system, the output will become
active after the violation ends.
38 zone trouble the output signals that the maximum zone violation time or the maximum zone no
violation time have been exceeded.
39 no guard code the output is activated by a timer programmed as the partition control TIMER,
unless a guard code is entered within the timer specified time.
40 service mode status the output is activated if the control panel service mode has been called from
any keypad.
41 battery test resultthe output whose state is updated after each battery voltage test.
Partitions
Creation of a partition consists in assigning at least 1 zone to it. The CA-10 permits
4 partitions to be created. Any outputs, telephone numbers and pager messages can be
assigned to one partition, thus enabling four independent alarm systems to be built on the
basis of one CA-10 control panel.
In the event of a few keypads being connected to the control panel, each keypad will be
hooked up to the particular partition via a special control output. The keypad connected to the
CLK1 output will belong to the partition 1, that connected to the CLK2 output – to the partition
2, etc.
Where the system comprises less keypads than partitions, individual partitions can be
operated from the existing keypads, by means of the GO TO function (when this function is
called, the keypad will for a time belong to another partition). The partition which has no
keypad, can be controlled through the zones to which the "arming" and "disarming" functions
are assigned. The state of such a partition can be signaled on the outputs.
Partitions can be defined in the following way:
partitions have no common zones – they are independent sub-systems,
some zones belong to several partitions the common zones are only armed when all
the partitions these zones belong to are armed,
all zones of one partition belong at the same time to another partition the control
panel recognizes one partition as the master, and the other as an internal one;
arming/disarming the master partition results in simultaneously
arming/disarming the
internal partition, while arming/disarming the internal partition only affects the zones within
that partition,
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Satel CA-10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Satel CA-10 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Satel CA-10

Satel CA-10 Gebruiksaanwijzing - Nederlands - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 4 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 64 pagina's

Satel CA-10 Aanvulling / aanpassing - Deutsch - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - Deutsch - 26 pagina's

Satel CA-10 Installatiehandleiding - Deutsch - 44 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 2 pagina's

Satel CA-10 Aanvulling / aanpassing - English - 60 pagina's

Satel CA-10 Aanvulling / aanpassing - English - 24 pagina's

Satel CA-10 Gebruiksaanwijzing - English - 24 pagina's

Satel CA-10 Snelstart handleiding - English - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info