470265
91
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
91
Appendix
Note:
The overlapping area might become uneven depending on the images. In such a case, it is recommended to
decrease the contrast of the images in the Image Adjust Menu or set the BrilliantColor function to ‘Off’.
If the colors of the left and right images do not match, then follow the next step.
Select ‘Color matching’ in the setting menu and display the Color matching dialog box.
Then, set ‘Color matching’ to ‘On’ and adjust the color settings (Red/Green/Blue/White).
(Refer to page 53 for operation procedure.)
6
Color matching
Note:
When you change the values of Target, make sure that each
Target value should be within the range of Measured value.
(e.g., In the case of the Fig.1, the X value of Target-Red
should be within 0.623 which is the X value of Measured-
Red.)
Set to ‘On.
5
Set ‘Test pattern’ to ‘On’ to display a 50 % white image. The overlap area will be brighter than the non-overlapping
area. Adjust the Black level in the Edge blending dialog box to increase the brightness of the non-overlapping area so
that the unevenness is reduced.
Select ‘Advanced color matching’ if you need further adjustment.
In the Advanced color matching dialog box, set ‘Advanced color matching’ to ‘On’ and adjust the values of Target (Red/
Green/ Blue/ Cyan/ Magenta/ Yellow/ White).
7
Fig.1 For rich color reproduction color wheel
If the colors of the left and right images do not match, even
if the Target values are adjusted, use a colorimeter which
is capable of measuring the chromaticity coordinates and
luminance. Follow the steps below.
1. Set ‘Auto test pattern’ to ‘On’ in the Advanced color
matching dialog box.
2. Put the cursor in the Mesured-White and press the
SELECT button to display a white pattern.
3. Measure the chromaticity coordinates (x,y) and
luminance (lx) by using the colorimeter.
4. Enter the obtained (x,y) values in the Mesured-White.
(The (L) value of Mesured-White should be left at 1.000.)
5. Put the cursor in the Mesured-Red and press the SELECT
button to display a red pattern.
6. Measure the chromaticity coordinates (x,y) and
luminance (Lx) by using the colorimeter.
7. Enter the obtained (x,y) values in the Mesured-Red. Then,
calculate the (L) value of Mesured-Red by applying the
following formula and enter the value.
(L) value of Mesured-Red = [Lx of Red] ÷ [Lx of White]
8. Enter the values of Mesured-Green, Mesured-Blue, and
Mesured-Half white in the same way as Mesured-Red.
9. Adjust the values of Target again.
10. Select ‘Store’ to complete. (Apply the same adjustment
to the other projector if necessary.)
8
91

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sanyo PDG-DET100L bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sanyo PDG-DET100L in de taal/talen: Engels als bijlage per email.

De handleiding is 10,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Sanyo PDG-DET100L

Sanyo PDG-DET100L Gebruiksaanwijzing - Deutsch - 92 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info