629823
13
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
9
Operating The ZM Series
Pre Announcement Chime
The ZM series mixer offers a useful Chime function to alert
listeners of an upcoming page. Simply press the front panel
Chime switch to play the chime.
In addition, the ZM series mixer can be set for one of four
selectable Chime tones by moving the internal shorting
jumpers as show in the figure below:
Priority Control
Channel 1 and 2 can be set for Priority operation. When
microphone channel 1 and 2’s Priority switch is set to the “ON
position, the other input channels will mute whenever signal
is present on the microphones connected to Channel 1 and 2.
Priority Mic Muting
In addition to the priority muting on microphones connected
to Channels 1 and 2, there are three levels of priority muting
which is always active. The priority muting is set in three
groups in the following order.
Chime and Tele page
Remote Mic
Channels 1 through 6
This means if there is a Tele-page or the Chime switch is
pressed, the Remote Mic and input Channels 1 through 6
are muted. If there is a signal on the Remote Mic, Channel
1 through 6 will be muted. The signals in the same priority
group will stay on together.
Connecting the Input Sources
Next, make the signal input connections, using the Euroblock
input connectors on the rear panel. If your mixer has balanced
outputs, we recommend the use of three-conductor cabling
and connectors (unbalanced two-conductor connections
can also be used, but you’ll get better signal quality and less
outside noise and hum if you use balanced lines).
On the front panel of the ZM Series, turn all the Channel input
controls fully counterclockwise (to their “MIN” setting). Then
connect the supplied heavy-gauge 3-pin “IEC” cable to the rear
panel IEC connector and to any grounded AC socket.
Press the front panel Power switch in order to turn on the ZM
Series. The Power LED will light and the Protection LED will go
on. After approximately five seconds, the Protection LED will
go off (you’ll hear a click when this occurs).
Apply an input signal to the ZM Series at or about +4dBu. Now
set the channel level to about half way up.
While the input signal is present, slowly raise the Master level
control until the desired sound level is achieved.
The SIGNAL and PEAK LED indicators will show you the
continuous power output of the ZM Series as signal is being
passed. For the best signal-to-noise ratio, the ZM Series
should normally be run with the Master level control at or
near maximum (fully clockwise, at the “MAX” position) and the
PEAK segments should light occasionally (but not frequently)
during peak levels. If the signal is too loud, use the Input level
controls attenuate the signals as necessary to achieve the
desired speaker level.
CD Player
Microphones
MIN MAX
ON OFF
PRIORITY
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Samson ZM75 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Samson ZM75 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Samson ZM75

Samson ZM75 Gebruiksaanwijzing - Français - 22 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info