629739
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
Connecting the Resound HD Speaker System
5
Choosing the Correct cables
The Resound HD series speaker connections are made via the rear panel 1/4-inch and/or Neutrik Speakon®
connectors. Standard, unshielded speaker wire, available at your local pro audio or music store, with either
1/4-inch phone or Speakon connectors and wire gauge of 12-14 is recommended.
If your amplifier uses binding posts you can use speaker cables with banana plugs, but be sure to pay atten-
tion to the plus and minus polarity when making the connections. It is important that your PA system is con-
nected in-phase otherwise you will not have the proper low-end response and stereo image.
In order to ensure that your PA system is-in phase, be careful to pay close attention to the positive and nega-
tive marking on the amplifier and wires. Make sure that the + terminal of the speaker, or banana connector,
is connected to the + terminal of the power amplifier and that the - terminal of the speaker, or banana con-
nector, is connected to the - terminal of the power amplifier.For a detailed wiring diagram, see page 9 of this
manual.
Heres a tip: Its fairly easy to identify a monitor that is out of phase just by listening, especially on a pop
recording. Listen for the parts of the music that you would expect to be in the center of the mix (like kick
drum and vocals). If you do not hear them directly in the center (for instance they sound like they are two
signals panned hard right and left), then you are more than likely listening to an out-of-phase monitor system.
(This test won’t work on early Beatles records where Ringos drum kit is panned all the to the right side. Try a
Madonna record.)
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about impedance. Impedance is
the electronic load that the speaker puts on the power amplifier and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance are wired in "Parallel",
like when you use the Extension Output, the total impedance is cut in half. When two speakers are wired in
“Series”, (usually for internal cabinet wiring only), the total impedance is the sum of the speakers individual
impedance.
Each of the Resound HD models, EXCEPT the RS215HD is 8 Ohms. So, when two Resound HD models (EXCEPT
the RS215HD) are connected together in parallel, the total impedance is 4 Ohms. The RS215HD impedance
is 4 Ohms. So, when two RS215HD’s are connected together in parallel, the total impedance is 2 Ohms. The
impedance of your speaker also has an effect on your amplifier. In general, the lower the impedance, the more
power your amplifier will put out.
IMPORTANT NOTE: There is minimum safe impedance for running power amplifiers so be sure to check the
manufacturers recommended impedance for your amplifier to avoid any damage to your amplifier or voiding
your warranty.
Using the EXTENSION Output
The Resound HD models provide a convenient Extension Output for connecting additional speaker cabinets
in parallel. Be sure to read the section above on impedance to insure a proper hook up with your amplifier. To
connect two Resound HDs using the Extension output, connect your amplifier output to the Input of the first
Resound HD and then, connect the Extension Output to the Input of the second Resound HD.
Powering the Resound HD
Each of the Resound HD loudspeakers have a specific power rating, which is printed on the input jack-plate,
and also, in the Specification section on page 10 of this manual. Be sure to check that your power amp has the
correct power output for your Resound HD. Be careful to consider the total impedance if you are connecting
more the one Resound HD to one side of a stereo power amplifier. Using a power amplifier with too low of a
power rating can be dangerous since the output signal is often clipped in an effort to get the desired level.
Over powering the Resound HD can result in catastrophic failure and therefore using any amplifier with a
power rating over the recommend power rating may void your warranty.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Samson RS10mHD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Samson RS10mHD in de taal/talen: Engels als bijlage per email.

De handleiding is 1,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info