735227
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Installation and Wiring Guide KL08RF
www.salus-controls.com Technical Helpline +44 (0) 1226 323 961
Installing and Connecting the KL08RF
Use the KL08RF wireless wiring centre to simply and safely connect thermostats and corresponding
thermal actuators. The KL08RF connects to the wireless network through the UG600/UGE600 universal
gateway for the internet systems and through the CO10RF coordinator for the non internet systems.
One universal gateway can support up to 100 devices and one coordinator can support up to nine
wiring centres, which means that if you buy more than one wiring centre, you will only need one
univeral gateway or one of the included coordinators. Keep the other coordinators in a safe place
as spares. Install the KL08RF only in dry and closed interior rooms. Relative air humidity in the room
may not exceed 95%. Clean the KL08RF only with a dry and soft cloth. Do not use solvents or aggressive
cleaning agents.
Remove the plastic
cover. Open (and
close) the four
white screws with a
quarter turn only. Note
that screws on opposite
sides turn in the opposite
direction.
2
Remove the
white terminal
connection board
3
Attach the back of
the KL08RF to the
DIN rail or wall.
4
Cut the power and
device cable to
length.
6
Push the power
wires into the
round power holes.
Attach the white
strain-relief using
the two screws to
secure the power wires.
8
9
Push in the Pump wires at the bottom
right of the KL08RF for volt-free pump
switching.
For 230V connections follow the wiring
diagram from the first page.
10
Push in the Boiler wires at the bottom
right of the KL08RF for volt-free boiler
switching. When a zone calls for heat,
the boiler switch closes causing the
boiler to run.
11
Push in the CO wires at the bottom
right of the KL08RF for volt-free
heating/cooling changeover switching.
An open switch is for heating (red LED).
A closed switch is for cooling (blue LED).
Note: Create the connections only for a
cooling system.
12
Push in the Dew Point wires at the
bottom right of the KL08RF for volt-free
humidity sensing.
13
Attach the red strain-relieving strip
using the three screws to secure the
pump, boiler, CO, and dew point wires
to the bottom side of the KL08RF.
14
Set the boiler delay, wireless, and thermal
actuator jumpers at the top right of the
KL08RF.
Jumper Settings/Positions for Pump/Boiler On/Off Delay
The pump/boiler on delay and the pump off
delay are fixed at 3 minutes in the software
and at 0 in the terminal. The default setting for
the boiler off delay is also 0 minutes, but can
be changed to 15 minutes. To do this, carefully
remove the jumper and re-insert it in the other
position as shown below:
Press the Reset button to complete this action.
Antenna
The default setting for the antenna is internal
(INT). To change this setting to external (EXT),
carefully remove the jumper and re-insert it in
the other position as shown below:
Press the Reset button to complete this action.
Type of Actuator
The default setting for the type of actuator is
normally closed (NC). To change this setting
to normally open (NO), carefully remove the
jumper and re-insert it in the other position as
shown below.
Press the Reset button to complete this action.
15
LED indications
Name Colour Meaning
Power
KL08RF is supplied with 230V power
G1
Wireless network activity on group 1 thermostats
G2
Wireless network activity on group 2 thermostats
Network Status
KL08RF is waiting to pair
KL08RF is connected to the wireless network
Zone 1 actuators
Demand from group 1, zone 1 thermostat: actuator open
Zone 2 actuators
Demand from group 1, zone 2 thermostat: actuator open
Zone 3 actuators
Demand from group 1, zone 3 thermostat: actuator open
Zone 4 actuators
Demand from group 1, zone 4 thermostat: actuator open
Zone 5 actuators
Demand from group 2, zone 1 thermostat: actuator open
Zone 6 actuators
Demand from group 2, zone 2 thermostat: actuator open
Zone 7 actuators
Demand from group 2, zone 3 thermostat: actuator open
Zone 8 actuators
Demand from group 2, zone 4 thermostat: actuator open
Pump
Pump on
Boiler
Boiler on
CO
Heating mode
Cooling mode
Push the thermal actuator wires into
the round holes at the bottom of the
KL08RF. You can connect up to three
actuators in each zone.
Make sure there is a fuse in the fuse
holder.
16
If you set up a non internet system, plug
in the CO10RF coordinator.
Reattach the
plastic cover.
Switch on mains
power supply to
the unit. The red
LED comes on.
18
7
Device
Power/Thermostat
50mm
110mm
10mm
10mm
If you need to install the optional
external antenna and have set the
Wireless jumpers to EXT:
a. Disconnect power.
b. Remove the protective
cap from the antenna
connection on the
underside of the
KL08RF.
c. Screw the antenna into
the KL08RF.
d. Press the Reset button
to complete this action.
e. Reconnect power. The
KL08RF will now use
the external antenna
and not the internal
antenna.
17
Heating mode
Cooling mode
5
Reattach the
white terminal
connection board
1
19
Coordinator
Connecting the KL08RF (s) to the ZigBee Wireless Network
1. On powering up the KL08RF, actuator LEDs will light up green then go o, then the
Network Status LED ashes green.
2. Press and hold the button on the coordinator for ve seconds. The button ashes red to
indicate the coordinator is ready to pair. The Network Status LED on the KL08RF goes steady
green when connected.
3. Repeat the process for every KL08RF in the system. Note that one coordinator can support
up to nine KL08RFs.
4. To identify your KL08RF (WC) number press Pair for one second. The LED on the zone
number lights green: WC -1=Zone 1, WC-3=Zone 1, 2, 3, and so on. The Network Status LED is used to identify WC-9
5. To pair your Salus thermostats, see your thermostat manual.
6. Press the coordinator button for ve seconds until the LED ashes steady red.
Note: To restore the KL08RF back to factory default settings at any time, press and hold the pair button on the KL08RF for 15
seconds. The G1 and G2 LEDs turn from ashing red to solid red then go o. After that please press the Reset button once.
Checking the System Conguration and Communication
Press and hold the coordinator button for one second. All devices connected to the system ash. To stop checking, press and
hold the coordinator button again for one second.
Press and hold the Pair button on the WC for ve seconds. All devices connected to the KL08RF will ash. To stop checking,
press and hold the Pair button again for ve seconds.
Deleting all Devices from the Wireless Network
To delete all devices connected to the network, press and hold the coordinator button for 15 seconds. The colour of the
button changes from red to amber.
To delete all devices connected to the KL08RF, press and hold the pair button on the KL08RF for 15 seconds. The G1 and G2
LEDs turn from ashing red to solid red then go o. The nal step is to press the Reset button once.
Note: After all devices have been deleted from the wireless network, they will need to be reinstalled. Refer to the instruction
manuals.
Universal Gateway
Connecting the KL08RF (s) to the ZigBee Wireless Network
1. On powering up the KL08RF, actuator LEDs will light up green then go o, then
the Network Status LED ashes green.
2. Remove the coordinator from the KL08, access the SALUS SmartHome App and
add your KL08RF. When in Pairing Mode, the Universal Gateway will start ashing
red. The Network Status LED on the KL08RF goes steady green when connected.
3. Repeat the process for every KL08RF in the system. Note that one Universal
Gateway can support up to 100 devices (thermostats, TRV’s, etc.).
4. To identify your KL08RF (WC) number press Pair for one second. The LED on the
zone number lights green: WC -1=Zone 1, WC-3=Zone 1, 2, 3, and so on. The
Network Status LED is used to identify WC-9.
5. To pair your SALUS thermostats, see your thermostat manual.
6. The Universal Gateway will turn solid blue automatically, once the pairing process is complete.
Note: To restore the KL08RF back to factory default settings at any time, press and hold the pair button on the KL08RF for 15
seconds. The G1 and G2 LEDs turn from ashing red to solid red then go o. After that please press the Reset button once.
Checking the System Conguration and Communication
Go to the SALUS SmartHome App and press the Identify button. The device will start ashing. Stop the identify process by
pressing the button from the App again.
Press and hold the Pair button on the WC for ve seconds. All devices connected to the KL08RF will ash. To stop checking,
press and hold the Pair button again for ve seconds.
Deleting all Devices from the Wireless Network
You can remove your devices from the SALUS SmartHome App, Equipment, All equipment menu.
To delete all devices connected to the KL08RF, press and hold the pair button on the KL08RF for 15 seconds. The G1 and G2
LEDs turn from ashing red to solid red then go o. The nal step is to press the Reset button once.
Note: After all devices have been deleted from the wireless network, they will need to be reinstalled. Refer to the instruction
manuals.
0
0
Old version New version
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Salus KL08RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Salus KL08RF in de taal/talen: Engels als bijlage per email.

De handleiding is 5,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info