735236
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
NSB Mode depends on the NSB wired connection.
0V=NSB OFF
230V=NSB ON
This function will be activated only when the device is running in Auto Mode.
If the thermostat receives a NSB signal then it will switch to - . If the NSB is turned
off, the unit will function in and . You can manually set the thermostat on NSB
by moving the box on the icon.
4. Button Functions
Mode selection.
Long press to return home without saving.
OK key. Short press to confirm selection.
Long press to save and return home.
Long press to enter Temperature offset Heat/Cool.
Decrease or increase Setpoint Temperature.
In Auto Mode by tapping
the or key you
can view the Setpoint
Temperature.
In Auto Mode by holding
the or key you will
access Manual Override
Mode.
After selecting the
temperature press
and the will appear.
Note: In Auto Mode the change in Manual Override Mode is temporary. This is
indicated by the icon. When used as a stand alone, the change is permanent.
In Sunny/ Moon/ Frost
Mode by tapping the
or key you will access
Manual Override Mode.
In Sunny/ Moon/ Frost
Mode the change will be
permanent.
When Auto Mode is
selected again the
permanent override
will end.
5. Frostschutz
Move the box by tapping
or on the Frost
Mode Indicator The device
will enter in Frost Mode.
In Frost Mode you can
select a temperature
between 5°-17°C.
Press the or key to
set the temperature.
Note: During the set-up, press at any time to return to the previous screen or
long press to return to Home display.
Product Compliance & Safety Information
Product Compliance
SALUS Controls hereby declares that the product complies with the essential
requirements of the following EC Directives: 2014/30/EU, 2014/35/EU and
2011/65/EU. The full text of the EU Declaration of Conformity is available at the
following internet address: www.saluslegal.com.
Safety Information
Use in compliance with safety regulations. The unit is to be used for the control of room
temperature inside the house.
Installation
This accessory must be fitted by a competent person, and installation must comply with
the guidance, standards and regulations applicable to the city, country or state where the
product is installed. Failure to comply with the relevant standards could lead to prosecution.
Note: All electrical installation work should be carried out by
a suitable qualified electrician or other competent person.
Product Description
Thank you for purchasing the SALUS HTRS230 Thermostat. This thermostat is a
device that lets you customise the heating and cooling of your home as needed.
The HTRS230 device from SALUS Controls is a stylish and accurate digital room
thermostat that is fitted with a large easy to read LCD screen and one touch
buttons. You can now simply adjust your home temperature as desired in order
to create a comfortable home environment.
We hope you enjoy our product.
Contents of the box
Manual Contents:
Box Contents
Introduction
Product Compliance and
Safety Information
Installation
User Interface
Status/LED indication
Installers notes
Warranty
Icons used in this manual:
Safety
Important info
Your benefit
Fixing Screws
1 x Installer Manual
Digital Thermostat
Model: HTRS230
INSTALLER MANUAL
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road,
Dodworth, Barnsley S75 3SP, UK.
Sales: T: +44 (0) 1226 323961
E: sales@salus-tech.com
Technical: T: +44 (0) 1226 323961
E: tech@salus-tech.com
www.salus-controls.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls
plc reserve the right to change specification, design and materials of
products listed in this brochure without prior notice.
Issue Date: Dec 2015
00086/2
For PDF Installation guide please
go to www.salus-manuals.com
Warranty
SALUS Controls warrants that this product (HTRS230) will be free from any
defect in materials or workmanship, and shall perform in accordance with
its specification, for a period of five years from the date of installation. SALUS
Controls sole liability for breach of this warranty will be (at its option) to repair
or replace the defective product.
Customer Name: ......................................................................................................................................
Customer Address: .................................................................................................................................
.............................................................................................................................................................................
....................................................................................... Post Code: ............................................................
Tel No: ................................................................ Email: .............................................................................
Engineers Company: .............................................................................................................................
Tel No: ................................................................ Email: .............................................................................
Instalation Date: .......................................................................................................................................
Engineers Name: ......................................................................................................................................
Engineers Signature: .............................................................................................................................
8. Setting the Thermostat
Device
No
Function Values Denition Default
Value
d01 Heating control 0 PWM 0
1 On-Off: 0.5°C(±0.25°C)
2 On-Off: 1.0°C(±0.5°C)
d02 Room temp offset -3.0°C to
+3.0°C
Offset room temp measuring
error(in 0.5°C)
0.0°C
d05 Cooling control 1 On-Off: 0.5°C(±0.25°C) 2
2 On-Off: 1.0°C(±0.5°C)
d07 Valve protection 0 Disable 1
1 Enable
d08 Frost Setpoint 5.0-17.0°C 5.0°C
d12 Max. heating setpoint 5.0-35.0°C 35.0°C
d13 Min. cooling setpoint 5.0-40.0°C 5.0°C
d18 Heating/Cooling
Mode
0 No connection 0
1 Connection
d19 Cooling Blocked 0 Cooling allowed 0
1 Cooling disabled
11. Factory Reset 14. Technical Specification
12. Heating/Cooling Mode
13. Temperature Offset (TemperatureCalibration)
Press the indicated keys
together for 3 seconds.
Long press in order to
enter in Settings Mode.
Press to confirm
Press to confirm
Select P47 if you want to
reset to factory settings.
Press to confirm
Note: In order to
quickly reach 47 you
can hold down
key. The display will
fast forward to step 5.
9. Setting the Thermostat
Note: The d20 will help you to reduce the power outlet on
the thermostat.
Setting the hysteresis
You can set the hysteresis by entering in Installer Mode, accessing d01 and after
that selecting the desired value ( PWM / 0.5°C / 1.0°C ).
Heating and Cooling Selection
Manually
The mode will be indicated by the flashing icons
Press or to change the modes.
Auto
The CO terminal needs to be connected.
After that the heating and cooling functions will be done automatically.
In Installer Mode, d19 has to be set on 0.
10. Setting the Thermostat
Cooling blocked
When the thermostat is set on Cooling Disabled (d19-->1) it will block the
cooling function for single rooms until the device will receive the heating
command. During the periods of Cooling Blocked no special indicator will be
displayed on the LCD screen. Cooling mode indicator will also be turned off.
Protection
When room temperature is over the limit of 36°C, all heating outputs will be
turned off regardless of the control pattern and delay timers. When room
temperature is under the limit of 4°C, all cooling outputs will be turned off
regardless of the control pattern and delay timers.
Heating Mode Cooling Mode
Temperature Mode Heating Cooling
Sunny 20.0ºC 20.0ºC
Moon 17.0ºC 26.0ºC
Frost (heat system)
5ºC -
The Temperature Offset can be set at any value between
-3°C and +3°C. Press OK to confirm.
Model: HTRS230
Operating Voltage: 230VAC / 50Hz
Max Switching Current: 0,5A
Max No. Actuators: 5pc
Hysteresis: 0,5C /1C
Size: 85mm / 85mm / 25mm
Humidity: 60ºC, 85% RH
Temp Range: 5ºC - 40ºC
Storage Temp: -25ºC - 60ºC
Safety Class: IP30
Certification: CE, ROHS II
HRTS230 Thermostat
Gently remove front housing and make the
wiring connections.
2. Terminal Connection
N
N
L
CO
L
ACTUATOR
E.G.
HEAT
PUMP
EXTERNAL
CLOCK
230VAC
50Hz
1. Mounting the Thermostat
N
CO
L
Note: You can wire the thermostat directly to the
KL04NSB, KL08NSB wiring centre or to an actuator
(purchased separatly).
3. Thermostat Icons
BOX means to select mode.
e.g. means Hi temp is selected
means the Hi temp is not selected.
Sunny: Hi comfortable temperature
Moon: Low comfortable temperature
Indicates AUTO ON or AUTO OFF
Frost Protection Indicator:
Frost protection is active, not available in cooling mode.
Heat Mode indicator: Indicates heating is running
Cood Mode indicator:
The icon is flashing when cooling mode active
Temperature indicator
• Display the room temperature
• Display the set temp
Temporary override indicator: If the set temperature is changed
when in program mode, the hand will appear until the next
programs starting time.
OR
You can change the Modes by tapping or and position the box on
the desired one.
Note: The NSB function will be available only when you also have another device
that can send a NSB signal (HTRP230 thermostat, external clock, NSB switch or
another clock thermostat).
6. Night Setback Function (NSB)
7. Installer Mode
Select P49 if you want to
enter Installer Mode.
Press to confirm.
You have reached the
Installer Mode. Select
your options by using
or and then confirm
by pressing .
Note: This function allows you to
customise your thermostat as you
desire. To select the device level
use to jump to the next one d1
> d2 > d5. On the desired level press
then you can choose your
preferences by using or .
Press the indicated keys
together for
3 seconds.
Note: LCD backlight is activated by pressing any key.
Wall mounting
For wall mounting, mark the correct
possition on the wall and mount the
rear case to the wall.
Install the HTRS230 digital room thermostat at roughly 1.5m above floor level. It should
be mounted in a location where the thermostat is easily accessible and away from direct
sunlight. You can mount the thermostat directly on the wall or you can install it on top of a
wall-box.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Salus HTRS 230 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Salus HTRS 230 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Salus HTRS 230

Salus HTRS 230 Gebruiksaanwijzing - Nederlands - 2 pagina's

Salus HTRS 230 Gebruiksaanwijzing - Deutsch - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info