661048
42
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
8
40-SPIRIT (SA1733)
Pos: 15.8 /Innenteil/Starten des Motors/Starten des Motors Text SAU11379H, SAU12178 (SA1438, SA1439) @ 29\mod_1393416274830_1521.docx @ 228409 @ @ 1
Push and hold the safety control bar (2) on the top tube (3) D .
Slowly pull the starter cable (4) until resistance is felt, then rapidly pull it out E
the engine begins to run, slowly recoil the cable.
Pos: 15.9 /Innenteil/Starten des Motors/Hinweis: bei optimaler max. Drehzahl (fix speed) @ 12\mod_1257778281828_1521.docx @ 98683 @ @ 1
The engine runs with optimum power at maximum speed, which is required for a clean
cutting pattern (engine speed = blade speed).
Pos: 15.10 /Innenteil/Beschreibung der Bauteile/40-SPIRIT (SA1333), R40 (SA1308) @ 45\mod_1470736771854_0.docx @ 514299 @ @ 1
40-SPIRIT (SA1333), R40 (SA1308)
Pos: 15.11 /Innenteil/Starten des Motors/Starten des Motors Text SAU13340 @ 34\mod_1412933360251_1521.docx @ 248666 @ @ 1
Press the primer – pump* (1) three to five times up to the limit (also if the engine
has stopped because of lack of fuel, refill the fuel and press the primer three to
five times) B .
NOTE
Initial pumping is normally unnecessary when a hot engine is restarted. However, in
cold weather it can be necessary to initially pump the fuel.
Push and hold the safety control bar (2) on the top tube (3) D .
Slowly pull the starter cable (4) until resistance is felt, then pull out quickly E , –
the engine begins to run, slowly recoils the station.
If the engine does not start after 3 pulls, press the primer three to five times and
then pull the starter cable again.
*is located on the left-hand side of the engine (in direction of movement)
Pos: 15.12 /Innenteil/Starten des Motors/Hinweis: bei optimaler max. Drehzahl (fix speed) @ 12\mod_1257778281828_1521.docx @ 98683 @ @ 1
The engine runs with optimum power at maximum speed, which is required for a clean
cutting pattern (engine speed = blade speed).
Pos: 15.13 /Innenteil/Beschreibung der Bauteile/Alle Modelle_dl_text_bold_8 @ 33\mod_1409212920947_1521.docx @ 245827 @ @ 1
All models
Pos: 16.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 16.2 /Innenteil/Abstellen des Motors/1 ABSTELLEN DES MOTORS (Abbildung F ) Benzin @ 5\mod_1169129514667_1521.docx @ 31705 @ 1 @ 1
11 SWITCHING OFF THE ENGINE (Illustration F )
Pos: 16.3 /Innenteil/Abstellen des Motors/Abstellen des Motors Text JS63, 40er @ 3\mod_1158833165366_1521.docx @ 20393 @ @ 1
Release the safety control bracket.
Pos: 16.4 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 16.5 /Innenteil/Abstellen des Motors/1 ANHALTEN IM NOTFALL @ 5\mod_1183556328817_1521.docx @ 36114 @ 1 @ 1
12 EMERGENCY STOPPING
Pos: 16.6 /Innenteil/Abstellen des Motors/Anhalten im Notfall Text o.A. Benzin @ 5\mod_1183556795103_1521.docx @ 36166 @ @ 1
Release the safety control lever.
The blade will stop.
The engine will stop.
Pos: 16.7 /Innenteil/Abstellen des Motors/Anhalten im Notfall Hinweis JS63, Benzin o.A. @ 26\mod_1377182032310_1521.docx @ 192800 @ @ 1
NOTE
Before every mowing job, make sure that the safety control bar for the engine
brake is working perfectly.
when the safety control bar is released, the engine and cutter bar must come
to a standstill within three seconds.
If this is not the case, please consult your nearest authorised workshop.
Pos: 17.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 17.2 /Innenteil/Grasfangeinrichtung/1 GRASFANGEINRICHTUNG @ 0\mod_1115360086375_1521.docx @ 1789 @ 1 @ 1
13 GRASS COLLECTOR
Pos: 17.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Messer, Stein, MotorStop @ 0\mod_1115360241546_1521.docx @ 1536 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 17.4 /Innenteil/Grasfangeinrichtung/1.1 Betrieb mit Grasfangsack @ 0\mod_1115360552250_1521.docx @ 1790 @ 2 @ 1
Operation with grass collector
Pos: 17.5 /Innenteil/Grasfangeinrichtung/Betrieb mit Grasfangsack Text 43er,47er @ 0\mod_1125908544003_1521.docx @ 1798 @ @ 1
While mowing, ensure that the collector is emptied in good time. The turbo signal on the
collector will indicate when the collector should be emptied.
Pos: 17.6 /Innenteil/Grasfangeinrichtung/Betrieb mit Grasfangsack Hinweis 32er, 36er, 40er Elektro @ 3\mod_1157376302287_1521.docx @ 18763 @ @ 1
IMPORTANT
Make sure that the chute (1) S1 is not bent when handling the collector.
Pos: 17.7 /Innenteil/Grasfangeinrichtung/1.1 TurboSignal (Füll-Anzeige des Grasfangsacks) (Abbildung J + K) @ 0\mod_1125908385641_1521.docx @ 1796 @ 2 @ 1
Turbo signal (shows when the grass collector is full)
(Illustration J + K )
Pos: 17.8 /Innenteil/Grasfangeinrichtung/Turbo Signal Text @ 1\mod_1132230723035_1521.docx @ 5567 @ @ 1
There is an indicator on the top of the collector that shows whether the collector is
empty or full:
The collector indicator inflates if the collector is empty and during the mowing J .
If the collector is full, the indicator collapses; once this happens, stop mowing
immediately and empty the collector K .
Pos: 17.9 /Innenteil/Grasfangeinrichtung/Turbo Signal Hinweis1 @ 0\mod_1115360987468_1521.docx @ 1803 @ @ 1
IMPORTANT
If the fabric of the grass collector is very dirty the turbo indicator will not inflate –
in this case, clean the fabric immediately. The grass collector will only collect
grass perfectly if it is permeable to air.
Pos: 17.10 /Innenteil/Grasfangeinrichtung/Fangsack reinigen @ 0\mod_1115361049609_1521.docx @ 1804 @ @ 1
IMPORTANT
Do not clean the grass collector with hot water!
Pos: 17.11 /Innenteil/Grasfangeinrichtung/1.1 Entleeren des Grasfangsacks (Abbildung L) @ 0\mod_1125908294476_1521.docx @ 1794 @ 2 @ 1
Emptying the grass collector (Illustration L )
Pos: 17.12 /Innenteil/Grasfangeinrichtung/Entleeren des Grasfangsacks Text 40er @ 4\mod_1159955735455_1521.docx @ 21573 @ @ 1
Switch off engine.
Lift ejection flap.
Unhinge the full grass collector from the mower at the carrying strap – the ejection
flap closes automatically.
Empty the collector thoroughly whilst holding it by the carrying strap and on the
bottom.
Pos: 17.13 /Innenteil/Grasfangeinrichtung/1.1 Betrieb ohne Grasfangsack @ 0\mod_1115361420062_1521.docx @ 1791 @ 2 @ 1
Operation without grass collector
Pos: 17.14 /Innenteil/Grasfangeinrichtung/Betrieb ohne Grasfangsack Hinweis @ 0\mod_1115361442640_1521.docx @ 1800 @ @ 1
WARNING
When mowing without grass collector the ejection flap on the mower housing
must always be closed (flap down).
Pos: 18.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 18.2 /Innenteil/Mähbetrieb/1 MÄHBETRIEB @ 0\mod_1115358011109_1521.docx @ 1769 @ 1 @ 1
14 MOWING
Pos: 18.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Lesen, Messer, Stein, Abstand, MotorStop @ 0\mod_1115358236734_1521.docx @ 1531 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 18.4 /Innenteil/Mähbetrieb/1.1 Mähen an Hanglagen @ 0\mod_1115358422453_1521.docx @ 1771 @ 2 @ 1
Mowing on slopes
Pos: 18.5 /Innenteil/Mähbetrieb/Mähen an Hanglagen Sicherheitshinweis 25° Benzin @ 38\mod_1439983053439_1521.docx @ 410856 @ @ 1
NOTE
The mower can be used on banks and slopes with a gradient of up to 46% (25°
angle). Any steeper slopes can lead to engine damage.
For safety reasons, however, we urgently recommend you do not exploit this
theoretical performance potential. Always make sure you have a firm stance.
Manually guided lawnmowers should never be used for slopes with a gradient in
excess of 26% (15° angle of slope). Stability may be lost!
Pos: 18.6 /Innenteil/Mähbetrieb/1.1 Ölstandkontrolle @ 0\mod_1115358654859_1521.docx @ 1772 @ 2 @ 1
Checking the oil level
Pos: 18.7 /Innenteil/Mähbetrieb/Ölstandkontrolle Mäher Text @ 0\mod_1115358693671_1521.docx @ 1779 @ @ 1
Check oil level each time prior to mowing Y1 . Never let the engine to run with too little
or too much oil. Irreparable damages could occur.
Pos: 18.8 /Innenteil/Mähbetrieb/1.1 Prüfung der Betriebssicherheit @ 0\mod_1115358766390_1521.docx @ 1773 @ 2 @ 1
Checking operating safety
Pos: 18.9 /Innenteil/Mähbetrieb/Prüfung der Betriebssicherheit Text Benzin o.A. + Text DLG @ 37\mod_1436258081976_1521.docx @ 401307 @ @ 1
The lawnmower is equipped with a motor stop device.
Before every mowing job, make sure that the motor stop safety control bar is working
perfectly. When the control bar is released, the motor and cutter bar must come to a
standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the engine has been started, the blade rotates and a wind-like noise can be heard.
The run-on time corresponds to the duration of the wind-like noise after the engine has
been stopped, it can be measured using a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid risk, check the condition and firm attachment of the blade before every
mowing job. The blade attachment screw must always be tightened by an authorised
workshop. If the blade screw is too tight or too loose, the blade coupling and cutter bar
can become damaged or loose which can lead to serious injuries. A worn or damaged
blade must always be replaced. (Refer here to the chapter "Cutter blade care").
In addition, check the fan, blade coupling and fan housing every 10 operating hours for
wear and a tight fit. Also check equipment screws and nuts for a firm fit and tighten if
necessary.
Make sure the spark plug connector is fitted tightly. Contact is only dangerous if the
plug connector has not been installed correctly. Never pull the plug connector off with
the engine running. Danger: electric shock.
If the mower mechanism becomes blocked e.g. by colliding with an obstacle, have an
authorised workshop check whether any parts of the mower are damaged or deformed.
Always have any necessary repairs done by an authorised workshop too.
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Pos: 18.10 /Innenteil/Mähbetrieb/1.1 Zeitliche Einschränkungen @ 0\mod_1115358910000_1521.docx @ 1775 @ 2 @ 1
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sabo R40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sabo R40 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info