661054

Sabo 43-COMPACT Handleiding

42
Verklein
Vergroot
Pagina terug
1/100
Pagina verder
8
To charge the battery, see section “Charging the starter battery”.
Pos: 14.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 14.2 /Innenteil/Vor der Ersten Inbetriebnahme/1 VOR DER ERSTEN INBETRIEBNAHME MÄHER @ 0\mod_1115210527828_1521.docx @ 1709 @ 1 @ 1
9 BEFORE USING THE LAWNMOWER FOR THE FIRST TIME
Pos: 14.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Stein @ 0\mod_1115200949078_1521.docx @ 1537 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 14.4 /Innenteil/Vor der Ersten Inbetriebnahme/Allgemeine Sicherheitshinweise Benzinmäher + Text DLG @ 37\mod_1436248174398_1521.docx @ 400215 @ @ 1
Check all screw connections and the spark plug connector for a tight fit. Tighten the
screws if necessary! Attachment of the cutter bar must be checked in particular (refer
here to the chapter "Cutter bar care").
The blade attachment screw must always be tightened by an authorised workshop. If
the blade screw is too tight or too loose, the blade coupling and cutter bar can become
damaged or loose which can lead to serious injuries.
The lawn mower is equipped with a motor stop device.
Before using the equipment for the first time, make sure that the motor stop safety
control bar is working perfectly. When the control bar is released, the motor and cutter
bar must come to a standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the engine has been started, the blade rotates and a wind-like noise can be heard.
The run-on time corresponds to the duration of the wind-like noise after the engine has
been stopped, it can be measured using a stopwatch.
Pos: 14.5 /Innenteil/Vor der Ersten Inbetriebnahme/Sicherheits- und Schutzeinrichtungen ... dürfen nicht manipuliert oder deaktiviert werden!_dl_text @ 38\mod_1437988093850_1521.docx @ 402470 @ @ 1
Machine safety and protective devices must not be manipulated or disabled!
Pos: 14.6 /Innenteil/Vor der Ersten Inbetriebnahme/Darauf achten ... Schutzeinrichtungen ordnungsgemäß angebracht und nicht beschädigt sind! @ 37\mod_1436249863921_1521.docx @ 400691 @ @ 1
Make sure that all protective devices have been attached properly and are not
damaged.
Pos: 14.7 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Starterbatterie laden (nur bei Elektro-Start) MUSTER @ 16\mod_1331724962607_1521.docx @ 134338 @ 2 @ 1
Charging the starter battery (only for electro-start)
Pos: 14.8 /Innenteil/Vor der Ersten Inbetriebnahme/Starterbatterie laden Text @ 19\mod_1346309764780_1521.docx @ 151662 @ @ 1
– The starter battery is a maintenance-free dry battery
– Prior to the initial start-up, it should be charged with the original charger for
approx. 24 hours.
For safety reasons and to avoid battery damage, the battery may only be
charged within a building in dry rooms and not in direct sunlight.
– To avoid unnecessary power consumption, disconnect the power plug from the
charger after charging and disconnect the battery from the charger.
– Avoid storing discharged batteries for a long time without charging them.
– So that your battery is always ready-to-operate, we recommend you always charge
the battery for approx. 24 hours prior to and after each mowing season. Avoid total
discharges since this may result in a battery failure.
– To prevent unauthorised use of the mower, especially by children, always remove
the ignition key and disconnect the cable which leads from the battery to the starter
motor by removing the battery plug from the mating plug of the cable harness
when you store the lawn mower until the next mowing. However, you should do
this at least before you store the mower for the winter break.
– Store the battery in a dry, cool and frost-protected room.
Pos: 14.9 /Innenteil/Vor der Ersten Inbetriebnahme/Starterbatterie laden Hinweis 1 @ 1\mod_1132584496168_1521.docx @ 5831 @ @ 1
NOTE
The battery can be charged in the assembled or disassembled state.
Pos: 14.10 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Ladegerät (Abbildung R4)neu @ 18\mod_1340608414456_1521.docx @ 143327 @ 2 @ 1
Charger (Illustration R4 )
Pos: 14.11 /Innenteil/Vor der Ersten Inbetriebnahme/Ladegerät Text neu @ 28\mod_1386065996181_1521.docx @ 220110 @ @ 1
The charger is made up of two parts and must be put together before initial use.
Insert the country-specific plug (1) into the charger (2) and push it forwards until it clicks
into place.
IMPORTANT
Use the charger supplied only for charging the respective mower battery.
Equally, do not try to charge your mower using a different charger. You could
endanger yourself or damage your equipment.
For safety reasons and to avoid damage to the charger, it may only be used
indoors and in dry rooms and the battery must not be charged in direct sunlight.
Chafed or bent connection cables on the plug-charger can lead to an excessive
cable load. Chargers with damaged cables must be replaced.
Pos: 14.12 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Laden in eingebautem Zustand (Abbildung X1) @ 1\mod_1132583909266_1521.docx @ 5815 @ 2 @ 1
Charging in assembled state (Illustration X1 )
Pos: 14.13 /Innenteil/Vor der Ersten Inbetriebnahme/Laden in eingebautem Zustand Text @ 1\mod_1132584197754_1521.docx @ 5823 @ @ 1
– Remove the battery cable from the cable harness.
– Connect the battery cable to the original charging device and plug the charging
device into a 230 V socket.
Pos: 14.14 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Laden in ausgebautem Zustand (Abbildung W1) @ 1\mod_1132584704499_1521.docx @ 5839 @ 2 @ 1
Charging the battery in disassembled state (Illustration W1 )
Pos: 14.15 /Innenteil/Vor der Ersten Inbetriebnahme/Laden in ausgebautem Zustand 43er COMPACT E @ 5\mod_1183373428286_1521.docx @ 35632 @ @ 1
Removing the battery
– To remove the battery, take off the battery cable from the cable harness, loosen
the screws, take off the cover and take out the battery.
– Connect the battery cable to the original charging device and plug the charging
device into a 230 V socket.
Pos: 14.16 /Innenteil/Vor der Ersten Inbetriebnahme/Starterbatterie laden Wichtig @ 1\mod_1132584972284_1521.docx @ 5855 @ @ 1
IMPORTANT
Please do not connect the charger to the plug connector of the cable harness
since this can lead to a fault in the charger.
Pos: 14.17 /Innenteil/Vor der Ersten Inbetriebnahme/Starterbatterie laden Hinweis 2 neues Ladegerät @ 16\mod_1321442566989_1521.docx @ 132604 @ @ 1
NOTE
The red warning light on the charger lights up during the charging process and
goes out after charging has finished.
Pos: 14.18 /Innenteil/Vor der Ersten Inbetriebnahme/Einbau Batterie nach Aufladen Text @ 1\mod_1132643657170_1521.docx @ 5873 @ @ 1
– After charging the battery, refasten to the battery holder (if the battery was
dismounted for charging). Reconnect the battery cable to the cable harness prior
to mowing.
Pos: 14.19 /Innenteil/Vor der Ersten Inbetriebnahme/Entsorgung Batterie Text SABO+JD @ 19\mod_1346310238611_1521.docx @ 152121 @ @ 1
NOTE
As soon as the battery must be renewed for reasons of age or mechanical
damage, it should be handed in as hazardous waste to public collection points of
your community or your authorized dealer for proper disposal.
Pos: 14.20 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Öl einfüllen (Abbildung Y1 ) @ 0\mod_1115210961078_1521.docx @ 1711 @ 2 @ 1
Filling with oil (Illustration Y1 )
Pos: 14.21 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Explosion @ 0\mod_1115210618640_1521.docx @ 1527 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 14.22 /Innenteil/Vor der Ersten Inbetriebnahme/Öl einfüllen Hinweis Motor JS63 @ 3\mod_1158825745978_1521.docx @ 20353 @ @ 1
IMPORTANT
Avoid damage! Engine is delivered without oil. You must add oil before running
the engine.
Pos: 14.23 /Innenteil/Vor der Ersten Inbetriebnahme/Öl einfüllen Text Motor B&S 550 E-Series, 675EXi, 650 Quantum @ 44\mod_1469090694063_1521.docx @ 504533 @ @ 1
Before starting the engine for the first time, use a funnel to fill motor oil (quantity and
quality see technical data) having unscrewed the dipstick in this opening first.
– Set the mower on level ground.
– Slowly fill oil through the filler neck. Do not overfill. After filling the oil, wait for about
one minute and then check the oil level.
Insert the dipstick and screw it tight.
– Check oil level
Remove the dipstick. Use a clean cloth to wipe off the dipstick, then insert it again
and screw tightly. Then pull the dipstick out again and read off the oil level. The oil
must be at the full mark at the top (arrow). Replenish oil if necessary. The oil level
must not be higher than the full mark, however.
Insert the dipstick again and tighten.
– After initial filling, remove the "NO OIL" sign from the top of the engine.
Pos: 14.24 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Kraftstoff einfüllen @ 0\mod_1115211956203_1521.docx @ 1710 @ 2 @ 1
Filling with fuel
Pos: 14.25 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Explosion, Benzin @ 0\mod_1115211811093_1521.docx @ 1528 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 14.26 /Innenteil/Vor der Ersten Inbetriebnahme/Kraftstoff einfüllen Text @ 0\mod_1127830250803_1521.docx @ 1714 @ @ 1
– Only fill the tank with fresh and clean unleaded standard petrol.
Fuel with up to 10% ethanol is acceptable.
– Unscrew tank cap.
– Fill tank with fuel using a funnel up to max. lower edge of filling nozzle.
– Replace tank cap and screw tight.
Pos: 15.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 15.2 /Innenteil/Starten des Motors/1 STARTEN DES MOTORS @ 2\mod_1147094760724_1521.docx @ 12743 @ 1 @ 1
10 STARTING THE ENGINE
Pos: 15.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Fuss, Stein, Abstand @ 0\mod_1115212854781_1521.docx @ 1529 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 15.4 /Innenteil/Starten des Motors/Allgemeine Sicherheitshinweise Heckauswurf @ 26\mod_1377169184915_1521.docx @ 188188 @ @ 1
Only start the engine when you are standing behind the mower.
Always place the mower on a level area which is not covered with high grass (if the
grass is too high it will block the cutter bar start-up and make starting the mower more
difficult). When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the cutting tool is
pointing in the direction away from the user, but only as far as absolutely necessary. As
long as the mower has not been lowered to the ground again, both your hands must be
on the top part of the bar.
Pos: 15.5 /Innenteil/Starten des Motors/Starterseilgriff während des Startens fest umfassen Hinweis @ 13\mod_1280234045462_1521.docx @ 110218 @ @ 1
CAUTION
Hold the starter cable handle firmly when starting. The handle may otherwise slip
out of your hand. Risk of injury!
Pos: 15.6 /Innenteil/Starten des Motors/Hinweis: WICHTIG @ 0\mod_1115213366156_1521.docx @ 1737 @ @ 1
… 42 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Sabo 43-COMPACT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Sabo 43-COMPACT in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info