628373
5
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
REV. 01 Copyright@2011 SAB Teli division All rights reserved
Manual Goblin 700
Goblin 770 Manual
Goblin 770 Manual
Release 1.0 - December 2012
SAB HELI DIVISION S.R.L.
Via San Crispino, 47
47030 San Mauro Pascoli (FC) - ITALY
7 – Tail assembly
8 – Assembling the modules
9 – Installation of swashplate servos
10 – Installation of the ESC
11 – Installation of Flybarless unit and RX
12 – Installation of the motor
1 – Introduction
2 – Important notes
3 – Components and Box
4 – Carbon frame assembly
5 – Trasmission module
6 – Main rotor
INDEX
The Goblin
is a high performance radio controlled helicopter.
The design is original, moving away from traditional schemes, searching rationality for simplicity.
Our goal was to create a simple, high performance helicopter, with a minimum of mechanical components,
and simple maintenance.
Please read this user manual carefully, it contains instructions for the correct assembly of the model.
Please refer to the web site www.goblin-helicopter.com for updates and other important information.
Thank you for your purchase, and have a great time with your Goblin!
SAB Heli Division.
13 – Installation of the boom, Canopy
14 – Battery
15 – In flight
16 – Maintenance
17 – Exploded views
18 – Spare parts
1720mm
1410mm
420mm
210m
Main rotor diameter: 1720mm (with 770mm blades)
Main blade length: 770mm
Tail rotor diameter: 296mm
Tail blade length: 115mm
Main shaft diameter: 12mm
Tail shaft diameter: 6mm
Spindle diameter: 10mm
Weight including standard electronics: 4080g (excluding batteries).
Motor size: Maximum 64mm diameter, maximum height 64mm.
Battery compartment: 75x58x350mm.
SPECIFICATIONS
Copyright@2012 - SAB Heli Division - All rights reserved
Page 1
Chapter 1, Introduction
Use grease
(eg Tri-Flow
Synthetic Grease)
IMPORTANT NOTES
*This radio controlled helicopter is not a toy.
*This radio controlled helicopter can be very dangerous.
*This radio controlled helicopter is a technically complex device which has to be built and handled very carefully.
*This radio controlled helicopter must be built following these instructions. This manual provides the necessary information
to correctly assemble the model. It is necessary to carefully follow all the instructions.
*Inexperienced pilots must be monitored by expert pilots.
*All operators must wear safety glasses and take appropriate safety precautions.
*A radio controlled helicopter must only be used in open spaces without obstacles, and far enough from people to minimize
the possibility of accidents or of injury to property or persons.
*A radio controlled helicopter can behave in an unexpected manner, causing loss of control of the model, making it very
dangerous.
*Lack of care with assembly or maintenance can result in an unreliable and dangerous model.
*
Neither SAB Heli Division nor its agents have any control over the assembly, maintenance and use of this product.
Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release SAB Heli Division from
any responsibility or liability arising from the use of this product.
SAFETY GUIDELINES
*Fly only in areas dedicated to the use of model helicopters.
*Follow all control procedures for the radio frequency system.
*It is necessary that you know your radio system well. Check all functions of the transmitter before every flight.
*The blades of the model rotate at a very high speed; be aware of the danger they pose and the damage they may cause.
*Never fly in the vicinity of other people.
Indicates that for this
assembly phase you need
materials that are in
box xx, bag xx, tray xx.
NOTES FOR ASSEMBLY
P
lease refer to this manual for assembly instructions for this model.
Follow the order of assembly indicated. The instructions are divided into chapters, which are structured in a way that
each step is based on the work done in the previous step. Changing the order of assembly may result in additional or
unnecessary steps.
Use thread lockers and retaining compounds as indicated. In general, each bolt or screw that engages with a metal part
requires thread lock.
Factory pre-assembled components have been assembled with all the required thread lock and lubricants,
and have passed quality control. It is not necessary to disassemble and re-assemble them.
It is necessary to pay attention to the symbols listed below:
Use grease
(eg Vasellina Grease)
Important
Use retaining
compound
(eg Loctite 648)
Use CA Glue
Use retaining
compound
(eg Loctite 243)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 2
Chapter 2, Important Notes
ADDITIONAL COMPONENTS REQUIRED
*Electric Motor:
12S-14S – 380-520Kv
Maximum diameter 64mm,
Maximum height 64mm, pinion shaft diameter 6
*Speed controller:
minimum 120A, suggest 160A
*Batteries: 12-14S 4500-6000mAh
*1 flybarless 3 axis control unit
*Radio power system, if not integrated with the ESC
*3 cyclic servos
*1 tail rotor servo
*6 channel radio control system on 2.4 GHz
(See configuration examples on page 28)
The assembly process is described in the following chapters of
this manual. Each phase begins with a green frame which gives
the box, the bag with screws (and miscellaneous items), and the
foam tray with the components required for the phase.
TOOLS, LUBRICANTS, ADHESIVES
*Generic pliers
*Hexagonal driver, size 1.5,2,2.5,3,4mm
*4mm T-Wrench
*5.5mm Socket wrench (for M3 nuts)
*8mm Hex fork wrench (for M5 nuts)
*Medium threadlocker (eg. Loctite 243)
*Strong retaining compound (eg. Loctite 648)
*Spray lubricant (eg. Try-Flow Oil)
*Synthetic grease (eg. Tri-Flow Synthetic Grease)
*Grease (eg. Vasellina Grease)
*Cyanoacrylate adhesive
*Pitch Gauge (for set-up)
*Soldering equipment (for motor wiring)
Inside the main box:
Box 2: Canopy, Blade Holder.
Box 3: Boom, Blades, Tail blades, Carbon rod.
Box 4: Mechanical parts in 4 trays:
Tray 1: Main rotor
Tray 2: Carbon frame and tail rotor
Tray 3: Transmission
Tray 4: Main structure
Box 5: Bags
Box 6: Carbon parts
Box 7: Carbon parts
Inside the main box there are:
Copyright@2012 - SAB Heli Division - All rights reserved
Page 3
Chapter 3, Components and Box
4-Carbon Frame
The manufacturing process of the carbon parts
often leaves micro-burrs and sharp edges. We
recommend de-burring the edges to minimize
the risks of electrical wire cuts, etc.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 4
Chapter 4, Carbon Frame
Frame Spacer
(H0003-S)
......x10
Flat Head Cap Screw M2.5x5mm
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Stop Battery Plate
(H0150-S)
Shocket Head Cap Screw
M2.5x8mm
(HC020-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
ESC Support
(H0153-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Battery Tray
(H0002-S)
Socket Head Cap Screw M2.5x8mm
......x2
Copyright@2012 - SAB Heli Division - All rights reserved
Page 5
Chapter 4, Carbon Frame
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
ESC Support
(H0004-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing Washer M3
(H0007-S)
ESC Support
Assembly
Main Frame 1
(H0145-S)
......x2
Flat Head Cap Screw
M2.5x5mm
......x4
Socket Head Cap Screw
M3x10mm
Finishing Washer M3
......x3
Landing Gear Support
(H0005-S)
Cable Pass
(HA010-S)
Canopy Positioners
(H0159-S)
ESC Support
Assembly
Landing Gear Support
(H0005-S)
Note:
Landing Gear Support
(H0005-S)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 6
Chapter 4, Carbon Frame
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing Washer
M3
(H0007-S)
Finishing Washer M3
(H0007-S)
Battery Support
Assembly
Finishing Washer M3
(H0007-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Note:
Finishing Washer M3
Socket Head Cap Screw M3x10mm
..... x3
..... x3
Finishing Washer M3
..... x7
Socket Head Cap Screw M3x10mm
Battery Support
Assembly
Top holes: 70mm max height batteries.
Bottom holes: 75mm max height batteries.
..... x6
Canopy Positioners
(H0159-S)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 7
Chapter 4, Carbon Frame
Socket Head Cap Screw
M2.5x6mm
Button Head Cap Screw M4x10mm
(HC100-S)
Landing Gear Struts
(H0074-S)
Button Head Cap Screw M4x6mm
(HC096-S)
Button Head Cap Screw
M4x6mm
......
x4
Socket Head Cap Screw
M2.5x6mm
(HC018-S)
Red Landing Gear 1
(H0162-S)
Red Landing Gear 2
(H0162-S)
Sliding Landing Gear
(H0039-S)
Yellow Landing Gear 1
(H0106-S)
Sliding Landing Gear
(H0039-S)
Yellow Landing Gear 2
(H0106-S)
Landing Gear 2
Assembly
Socket Head Cap Screw
M2.5x6mm
(HC018-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Socket Head Cap Screw
M2.5x6mm
(HC018-S)
Landing Gear Struts
(H0074-S)
Button Head Cap Screw M4x10mm
(HC100-S)
Button Head Cap Screw M4x6mm
(HC096-S)
Landing Gear 1
Assembly
Button Head Cap Screw
M4x10mm
......
x4
.....x4
Copyright@2012 - SAB Heli Division - All rights reserved
Page 8
Chapter 4, Carbon Frame
5 - Transmission Assembly
Copyright@2012 - SAB Heli Division - All rights reserved
Page 9
Chapter 5, Transmission Assembly
Bearing
10x
19x5mm
(HC422-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
......
x1
Finishing Washer M3
(H0007-S)
Bearing
10x
19x5mm
......
x1
Servo Support
(H0010-S)
Bearing
12x
24x6mm
(HC426-S)
Bearing
12x
24x6mm
(HC426-S)
Socket Head Cap Screw
M3x10mm
......
x2
......
x1
......
x3
Swash plate Anti-Rotation Guide
(H0152-S)
Button Head Cap Screw
M3x4mm
(HC038-S)
Antenna Guide
(H0050-S)
Main Structure
(H0009-S)
Bearing Support Assembly
(H0024-S)
......
x1
......
x4
Button Head Cap Screw
M3x4mm
......
x1
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Socket Head Cap Screw
M3x8mm
Socket Head Cap
Screw M3x8mm
(HC050-S)
Bearing
12x
24x6mm
......
x3
Socket Head Cap
Screw M3x10mm
(HC056-S)
Column
(H0018-S)
Bearing
10x
19x5mm
Bearing
12x
24x6mm
Socket Head Cap Screw
M3x10mm
Flat Head Cap Screw
M2.5x5mm
Bearing
10x
19x5mm
(HC422-S)
Note:
Socket Head Cap
Screw M3x10mm
(HC056-S)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 10
Chapter 5, Transmission Assembly
......
x1
19T Drive Pinion
(H0156-S)
Metric Hex Nylon Nut M3
(HC206-S)
68T Main Gear
(H0012-S)
Metric Hex Nylon Nut M2.5
(HC200-S)
37T Pulley Assembly
(H0101-S)
M4 Locking Collar
(H0121-S)
Secondary Shaft
(H0157-S)
37T Pulley
(H0101-S)
Bearing
10x
15x4mm
One Way Bearing
10x
14x12mm
60T Pulley Assembly
(H0104-S)
Bearing
10x
15x4mm
Socket Head Cap Screw Shouldered
M2.5x19mm
(HC033-S)
Note 1:
When you tighten the collar (
H0127-S
) on
the main shaft, ensure there is no axial play. Push
down the main shaft while pulling up the locking
collar. Tighten the screw
M4x22
at this time.
Note 2:
The pinion and gear are designed to have zero
backlash. This leads to initial “rough” rotation.
After some run in flights (
3-5 flights
) it will begin
to rotate freely, ensuring perfect contact and
the ability to transmit maximum power.
It is advisable to lubricate these two elements
with a lubricant (eg Silicone or Tri-Flow Synthetic
grease).
......
x1
......
x1
Main Shaft
(H0127-S)
Main Structure
Assembly 1
Metric Hex Nylon Nut M3
Socket Head Cap Screw M4x22mm
......
x1
Socket Head Cap Screw
Shouldered M4x24mm
(HC111-S)
Socket Head Cap Screw Shouldered
M3x20mm
Socket Head Cap Screw Shouldered M4x24mm
......
x1
......
x1
Metric Hex
Nylon Nut M4
(HC212-S)
Metric Hex Nylon
Nut M4
(HC212-S)
Socket Head Cap Screw
M4x22mm
(HC104-S)
Socket Head Cap
Screw Shouldered
M3x20mm
(HC082-S)
60T Pulley
60T Pulley Assembly
(H0104-S)
Metric Hex Nylon Nut M4
......
x2
Socket Head Cap
Screw M2x8mm
(HC008-S)
37T Pulley Assembly
(H0101-S)
Bush OneWay
(H0110-S)
Metric Hex Nylon Nut M2.5
Socket Head Cap Screw Shouldered
M2.5x19mm
Washer
10x
16x0.2mm
(HC232)
Use if the play is more than
0.3/0.4mm.
Use this hole
Spacer Arm
3x
5x2.7mm
(H0134)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 11
Chapter 5, Transmission Assembly
Spring
de 8 / df0.5 / LL8
(HC315-S)
Flanged Bearing
5x
9x3mm
(HC410-S)
Flanged Bearing
3x
7x3mm
(HC402-S)
......
x1
......
x1
Flanged Bearing
5x
9x3mm
Nylon Screw M8x14mm
......
x2
Flanged Bearing
3x
7x3mm
......
x2
Metric Hex Nut M8
......
x2
......
x2
Tail Belt Idler
Washer
3x
4x0.5mm
......
x1
Washer
3.2x
6x0.5mm
(HC180-S)
Belt Tensioner Arm
......
x1
Washer
3x
4x0.5mm
(HC176-S)
Socket Head Cap Screw
M3x16mm
(HC068-S)
Button Head Cap Screw M3x4mm
Belt Tensioner Support
(H0070-S)
Socket Head Cap Screw M3x12mm
Socket Head Cap Screw M3x50mm
Metric Hex Nut M8
(HC224-S)
Nylon Screw
M8x14mm
(HC164-S)
Socket Head Cap Screw
M3x12mm
(HC062-S)
Tail Belt Idler Assembly
(H0070-S)
Belt Tensioner Arm Assembly
(H0070-S)
Washer
3.2x
6x0.5mm
(HC180-S)
Socket Head Cap Screw
M3x50mm
(HC092-S)
Main Structure
Assembly 3
Tail Belt Idler Assembly
(H0070-S)
Button Head Cap Screw
M3x4mm
(HC038-S)
Belt Tensioner Arm Assembly
(H0070-S)
Note:
Position without preload. Insert the screw in the
hole through the aluminum support as in the picture.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 12
Chapter 5, Transmission Assembly
Motor
Motor Support
(H0143-S)
Button Head Cap Screw M4x8mm
.....x2
Set Screw M5x20mm
(HC158-S)
Set Screw M4x4mm
.....x2
Finishing Washer
M3
(H0007-S)
.....x2
.....x2
.....x2
.....x4
Set Screw M5x20mm
Socket Head Cap
Screw M3x10mm
(HC056-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing Washer
M3
(H0007-S)
34mm
6mm
6mm
.....x2
7mm
0/0.2mm
Set Screw M4x4mm
(HC152-S)
Button Head Cap Screw
M4x8mm
(HC098-S)
20T Pulley
(H0015-20-S)
Lock motor pulley after
locking H0142
(see page 28 for optional
pulley selection)
Socket Head Cap Screw M3x8mm
Spring
HC314
(HC315-S)
Washer
5.3x
15x1mm
(HC188-S)
Metric Hex Nylon Nut
M5 Low
(HC218-S)
Spring
HC310
(HC315-S)
Washer
5.3x
15x1mm
Socket Head Cap Screw M3x10mm
Finishing Washer M3
Note:
To maximize space for the batteries,
it is advisable to shorten the motor
shaft.
Follow the dimensions given in this
drawing. For the cut, you can use an
electric tool like a “Dremel” with a
cut-off disc.
Additionally, ensure the motor shaft
has an appropriate 'flat' for one of
the set screws.
Socket Head Cap
Screw M3x8mm
(HC050-S)
Bearing Support (H0142-S)
Lock H0142 after have locked
the motor.Motor shaft is requires
to optimize the centering.
H0142 can not be used with motor
shaft 8mm.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 13
Chapter 5, Transmission Assembly
6 - Main Rotor
Copyright@2012 - SAB Heli Division - All rights reserved
Page 14
Chapter 6, Head HPS
Center Hub
(H0135-S)
Linkage Rod M2.5x48mm
(H0137-S)
Plastic Ball Link
(H0066-S)
Main Blade Grip
(H0034-S)
Bearing
10x
19x5mm
(HC422-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Uniball
M3x4
5H3
(H065-S)
Left Thread
Right Thread
Note
: Smaller ID
Blade Grip Arm
(H0136-S)
Uniball Radius Arm
Assembly
(H0205-S)
Washer
10x
16x0.2mm
(HC232-S)
Damper Derlin
(H0144-S)
Spindle
(H0079-S)
Uniball Radius Arm ... x 2
Assembly
Main Blade Grip Assembl
y ....x2
Note
: Larger ID
Button Head Cap Screw
M6x10mm
(HC122-S)
Washer
10x
16x1mm
(HC230-S)
Oring
(HA024)
Washer
6x
14 x1.5mm
(HC194-S)
Washer
10x
16x1mm
(HC230-S)
Thrust Bearing
10x
18x5.5mm
(HC438-S)
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Washer
3x4x0.5mm
(HC176-S)
Swashplate Assemly
Center Hub Assembly
Radius Arm
(H0132-S)
Uniball Radius Arm
(H0205-S)
Flanged Bearing
3x
7x3mm
(HC402-S)
Flanged Bearing
2.5x
6x2.5mm
(HC400-S)
Spacer Arm
2.5x4x6.3mm
(H0253)
Spacer Arm 3x5x2.7mm
(H0134)
Main Blade Grip
Assembly
Bearing
10x
19x5mm
(HC422-S)
Approx. 75mm
Radius Arm ... x 2
Assembly
Uniball
M3x4
5H3
(H065-S)
Uniball
M3x4
5H18
(H063-S)
Swashplate
Assemly
(H023-S)
Uniball
M3x4
5H3
(H0065-S)
SETUP LINKAGE
Linkage Rod A Assembly . . . .x2
Radius Arm
Assembly
(H0132-S)
The HPS head should be assembled with one, 1mm
shim (
HC230
) and one, 0.2mm shim (
HC232
) on
each side. In this way, the preload is medium.
(see page 33 for some info about.)
After approximately
10/20
flights, please check the
preload, you can add one or two 0.2mm shims
(
HC232
) if the preload has changed.
(Initial length for the rods from the swash plate
to the Blade Grip.)
Damper Derlin
(H0144-S)
Oring
(HA024)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 15
Head HPS
7-Boom and Tail
Copyright@2012 - SAB Heli Division - All rights reserved
Page 16
Chapter 7, Tail
......
x2
Flanged Bearing
3x
7x3mm
Bearing
5x
9x3mm
(H0052-S)
Bush Bell Crank
(H0059-S)
Bell Crank Lever
(H0059-S)
Uniball Spacer
(H0064-S)
Socket Head Cap Screw
M3x22mm
(HC086-S)
......
x1
Bell Crank Lever Assembly
......
x1
Tail Pitch Slider 01
(H0053-S)
......
x1
Socket Head Cap Screw
M3x22mm
Tail Blade Grip
(H0052-S)
Bearing
5x
9x3mm
......
x4
Tail Blade Grip Assembly .... x 2
(H0052-S)
Bell Crank Base
(H0058-S)
Washer
3x
4x0.5mm
Flanged Bearing
3x
7x3mm
(HC402-S)
Spacer
3x
4x9.6mm
(H0059-S)
Socket Head Cap
Screw M2x8mm
(H0008-S)
Uniball M2
5H6
(H0064-S)
Socket Head Cap Screw
M2x8mm
Washer
3x
4x0.5mm
Flanged Bearing
8x
12x3.5mm
(HC418-S)
Tail Pitch Slider 02
(H0053-S)
Spacer
8.1x
9.2x3.2mm
Tail Pitch Slider 03
(H0053-S)
Tail Pitch Slider Assembly
Uniball M3x3.5
5H3
(H0065-S)
Flanged Bearing
8x
12x3.5mm
......
x2
Copyright@2012 - SAB Heli Division - All rights reserved
Page 17
Chapter 7, Tail
Note
: Smaller ID
......
x2
Grip Link Bush
(HC056-S)
......
x2
......
x2
Set Screw
M4x4mm
(HC152-S)
Washer
3.3x
7x1mm
(HC181-S)
Tail Rotor Shaft
(H0048-S)
Socket Head Cap Screw M2x6mm
Tail Pitch Slider
Assembly
(H0053-S)
Thrust Bearing
4x
9x4mm
......
x2
Socket Head Cap Screw
M2x6mm
(HC004-S)
Tail Pitch Slider Link
(HC056-S)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Thrust Bearing
4x
9x4mm
(HC434-S)
Spacer
7x
9x5mm
(H0062-S)
Tail Rotor Hub
(H0051-S)
Tail Blade Grip
Assembly1
(H0052-S)
Socket Head Cap Screw
M2x12mm
(HC014-S)
Main Grip Link Bush
(HC056-S)
Socket Head Cap
Screw M2x12mm
(HC014-S)
Tail Pitch Slider Link Assembly
Tail Pitch Slider Link
Assembly
Socket Head Cap Screw
M2x12mm
......
x2
Tail Blade Grip
Assembly2
(H0052-S)
Spacer
7x
9x5mm
(H0062-S)
Thrust Bearing
4x
9x4mm
(HC434-S)
Socket Head Cap Screw
M3x16mm
(HC068-S)
Spacer
7x
9x5mm
Socket Head Cap Screw M3x16mm
Tail Rotor Hub Assembly
Tail Rotor Hub
Assembly
Washer
3.3x
7x1mm
(HC181-S)
Note
: Larger ID
Note
: Smaller ID
Note
: Larger ID
Copyright@2012 - SAB Heli Division - All rights reserved
Page 18
Chapter 7, Tail
......
x1
......
x1
......
x4
......
x1
Socket Head Cap Screw M2.5x8mm
Red Vertical Fin
(H0117-S)
Tail Side Plate
Assembly
Socket Head Cap Screw M3x8mm
Socket Head Cap Screw
M3x8mm
......
x4
Socket Head Cap
Screw M3x8mm
(HC050-S)
Tail Case Spacer
(H0061-S)
......
x2
25T Pulley
(H0155-S)
Set Screw M4x4
Bell Crank Lever
Assembly
Flanged Bearing
6x
13x5mm
(HC414-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Tail Side Plate
(H0047-S)
Flanged Bearing
6x
13x5mm
(HC414-S)
Yellow Vertical Fin
(H0046-S)
Vertical Fin Assembly
Tail Side Plate Assembly
Socket Head Cap Screw
M3x8mm
(HC050-S)
Tail System Assembly
Flanged Bearing
6x
13x5mm
Flanged Bearing
6x
13x5mm
Vertical Fin
Assembly
Belt Gates
2160-3MGT-06
(HC325-S)
Set Screw
M4x4
(HC152-S)
Tail Rotor Shaft
Assembly
Copyright@2012 - SAB Heli Division - All rights reserved
Page 19
Chapter 7, Tail
A
B
C
If you want to see a video of this operation,
consult the SAB Heli Division YouTube channel.
DETAIL A
SCALE 1 : 2.5
Washer
3.1x
12x1.8mm
(H0078-S)
Yellow Tail Boom
(H0147-S)
Red Tail Boom
(H0163-S)
DETAIL B
DETAIL C
SCALE 1 : 2
Metric Hex Nylon Nut M3
Linkage Tail Support
(H0045-S)
Tail Servo Lock
(H0040-S)
......
x2
Socket Head Cap Screw
M2.5x6mm
Set Screw
M3x20mm
(HC150-S)
Metric Hex
Nylon Nut M3
(HC206-S)
Washer
3.1x
12x1.8mm
(H0078-S)
Metric Hex Nylon Nut M3
(HC206-S)
Tail Boom
(H0147-S)
Locking Element
Tail Assembly
(H0041-S)
Locking Element Tail Assembly .... X 2
Metric Hex
Nylon Nut M3
......
x4
Boom Spacer
(H0082-S)
Set Screw M3x20mm
......
x3
......
x2
Note:
Metric Hex Nylon Nut M3
(HC206-S)
DETAIL A
DETAIL C
Tail Boom Assembly
(H0163-S)
Locking Element Tail
Attaching H0082-S to the boom:
Pre-assemble the two boom spacers H0082-S with
the M3x20 socket set screw.
Insert into the boom tube completely done up.
Center the holes, then unscrew until there is contact with the walls
Lock everything with the adhesive.
Assemble H0040-S in the boom
Before assembling the two parts in the boom we
suggest tightening the M2.5 screws into the two
plastic parts to pre-thread them. In this way when
you will assemble the tail servo it will be easier to
tighten the screws into the plastic parts. Check
the tail servo can fit, if necessary carefully sand
the hole.
Assemble H0045-S in the boom
Before mounting H0045 on the boom we
suggest to first tighten the M2.5 screws into
the holes to thread them. In this way when
you assemble the part it will be easier to
tighten the screws.
Tail Boom
(H0147-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Double
Sided Tape
Copyright@2012 - SAB Heli Division - All rights reserved
Page 20
Chapter 7, Tail
......
x4
Plastic Ball Link
(H0066-S)
Threaded Rod M2.5x40mm
(HC238-S)
A
DETAIL A
SCALE 1 : 1.7
Socket Head Cap Screw
M3x12mm
(HC062-S)
Finishing Washer M3
(H0007-S)
4mm
4mm
Approx 803mm
14mm
14mm
Socket Head Cap Screw M3x12mm
......
x4
Finishing Washer M3
Finishing Washer M3
(H0007-S)
Socket Head Cap Screw
M3x12mm
(HC062-S)
Tail Boom
Assembly
Plastic Ball Link
(H0066-S)
Carbon Rod
4x
2.5x752mm
(HC238-S)
Threaded Rod M2.5x40mm
(HC238-S)
Note:
Copyright@2012 - SAB Heli Division - All rights reserved
Page 21
Chapter 7, Tail
Socket Head Cap Screw M2.5x12mm
Tail Servo Assembly
The tail servo wire lead should be secured with hot
glue in the area indicated by the arrow (figure 1).
Figure 2 shows the installed servo.
Note: Please note that the boom edges might
be rough and can eventually chafe or cut your tail
servo lead - we recommend protecting the leads with
heat shrink or even electrical tape.
Tail Assembly
B
DETAIL B
SCALE 1 : 3.3
Servo Spacer
(H0075-S)
Carbon Rod Assembly
(HC238-S)
Socket Head Cap Screw
M2x6mm
(HC004-S)
Tail Servo Assembly
......
x4
Socket Head Cap Screw
M2.5x12mm
......
x1
Socket Head Cap Screw
M2x6mm
......
x1
Uniball M2
5H6
15-16mm
The distance between the
axis and the ball must be
between 15-16 mm
Uniball M2
5H6
(H0064-S)
Tail Servo
Copyright@2012 - SAB Heli Division - All rights reserved
Page 22
Chapter 7, Tail Servo Installation
Socket Head Cap Screw
M3x12mm
(HC062-S)
Finishing Washer M3
(H0007-S)
Socket Head Cap Screw Shouldered
M4x24mm
......
x6
......
x1
......
x8
......
x2
Socket Head Cap Screw M3x12mm
Socket Head Cap Screw M3x10mm
Finishing Washer M3
Metric Hex Nylon Nut M4
Canopy
Positioner
(H0008-S)
Socket Head Cap Screw
M3x10mm
(HC056-S)
Socket Head Cap Screw
M3x12mm
(HC062-S)
Carbon Frame
Assembly
Canopy Positioner
(H0008-S)
Head HPS
Assembly
Central Group
Assembly
Socket Head Cap Screw
M3x10mm
(HC056-S)
Metric Hex
Nylon Nut M4
(HC212-S)
Socket Head Cap Screw Shouldered
M4x24mm
(HC111-S)
Finishing Washer
M3
(H0007-S)
......
x1
Swashplate
Assembly
Copyright@2012 - SAB Heli Division - All rights reserved
Page 23
Chapter 8, Assembling The Modules
Assembly of the Ball on the Horn.
The rods going from the servos to the swash plate must be
as vertical as possible. Not all servos are equal, so to better
align them you can choose to use the supplied spacer
H0031. Figure 4 illustrates this.
INSTALLATION OF SWASHPLATE SERVOS
The linkage ball must be positioned between
16-18 mm
out on the servo arm (
figure 1
). The 120° placement of the servos inside Goblin means
the arms are difficult to access. For this reason it is advisable to ensure alignment of the servo arms (and sub trim set) before installation of
the servos in the model (
figure 2
). Proceed with installation following the instructions below.
Figure 3
shows a completed installation.
Uniball M2
5H6
(H0064-S)
Socket Head Cap Screw M2x8mm
(HC008-S)
or
Socket Head Cap Screw M2x6mm
(HC004-S) without Uniball Spacer
..... x3
Socket Head Cap Screw
M2.5x8mm
Servo 3
Servos Assembly 1, 2, 3
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Servo Spacer
(H0075-S)
Servo 1
Servo 2
Servo 3
Servo 1
Servo 2
Uniball Spacer
(H0064-S)
16-18mm
Socket Head Cap
Screw M2.5x12mm
(HC026-S)
..... x9
Socket Head Cap Screw
M2.5x12mm
Socket Head Cap Screw
M3x6mm
(HC044-S)
Note
: We recommend using
hight quality servo horn.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 24
Chapter 9, Installation Of Swashplate Servos
66mm
Approx.
54.5mm
Left Thread
Right Thread
The wire for the front servo must be positioned here.
If it is necessary to tighten the
horn screw, use the included
hexagonal wrench (HA002).
Tool HA002
Linkage Rod B
Assembly
Linkage Rod A
Assembly
(Initial length for the rods from the
servos to the swash plate.)
(Initial length for the rods from the swash plate
to the Blade Grip.)
Plastic Ball Link
(H0066-S)
Set Screw M2.5x40mm
(HC242-S)
Plastic Ball Link
(H0066-S)
Approx. 63.5mm
Linkage Rod B Assembly . . . . .x3
Approx. 75mm
Linkage Rod A Assembly . . . .x2
Linkage Rod M2.5x48mm
(H0137-S)
Head Preliminary Setup
Adjust the linkage as shown.
The linkage Rod A has thread right / left.
Turning, you can change the tracking without
disconnecting the plastic ball link.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 25
Chapter 12, Installation Of The Motor
DE-BURR THE SIDE FRAMES
We recommend de-burring the edges of the carbon parts in areas where electrical wires run.
ESC INSTALLATION
There are two mounting options:
Mount using part # H0004 (ESC Aluminum Support)
Typically used for Kontronik Jive 120. The speed controller is placed on top of the aluminum support. (Fig. 1)
Mount using part #H0153 (ESC Carbon Support) (Fig. 2)
Typically used for ESCs with aluminum cases, such as Kontronik Kosmik (Fig. 3). The speed controller is attached under the
carbon fiber plate.
A heat sink upgrade is available for the YGE 160 controller (Part #H0165-S) (Fig. 4)
Figure 5
: Shows the wiring which connects the receiver and ESC (in this picture one frame has been removed).
If the BEC used is combined with the ESC, it is recommended to use a dual wire connection.
Figure 6
: The passage of the controller wires to the motor is highlighted.
Figure 7
: Shows the installation of a 2S battery for the flight control system.
Alternatively, a BEC could be placed in the same area.
ESC Cables
2S Battery or BEC
Copyright@2012 - SAB Heli Division - All rights reserved
Page 26
Chapter 10, Installation Of The ESC
FLYBARLESS CONTROL UNIT AND RX INSTALLATION
It is possible to install any commercially available Flybarless control unit in the goblin.
For Flybarless systems with a separate sensor, the sensor must be installed under the plate (
Figure 1
).
Figure 2
shows an example of installation of the receiver and flybarless control unit.
In
Figure 3
you can see the extension lead for the tail servo. It is very important to include a connector for fast
disassembly of the boom module. The connector will prevent servo damage in case of boom separation during a crash.
Slot for sensor cable
It is important to lock the plugs of the
flybarless unit with an adhesive - for
example hot glue.
Tail servo extension cable
To install a one piece Flybarless system it is necessary to add the support shown in these figures. Figure 3 shows the installed
support. Figure 4 shows the control unit and the receiver installed on the support.
Support Flybarless
(H0043-S)
Spacer Support
Flybarless
(H0043-S)
RX
Flate Head Cap Screw M3x8mm
(HC134-S)
Socket Head Cap
Screw M3x6mm
(HC044-S)
Flybarless Unit
Socket Head Cap
Screw M3x6mm
(HC044-S)
Copyright@2012 - SAB Heli Division - All rights reserved
Page 27
Chapter 11, Installation Of Flybarless Unit and RX
TRANSMISSION SETUP
It is important to choose the right reduction ratio to maximize efficiency based on your required flight performance.
The Goblin has many possible reduction ratios at your disposal. It is possible to optimize any motor and battery combination.
It is recommended to use wiring and connectors appropriate for the currents generated in a helicopter of this class.
If you are using a head speed calculator which requires a main gear and pinion tooth count, use
215
teeth for the main gear
(this takes into account the two stage reduction) and the tooth count of your pulley as the pinion count.
Below is a list of available reduction ratios
:
H0015-18-S - 18T Pinion = ratio 11.93:1 H0015-22-S - 22T Pinion = ratio 9.75:1
H0015-19-S - 19T Pinion = ratio 11.3:1 H0015-23-S - 23T Pinion = ratio 9.35:1
H0015-20-S - 20T Pinion = ratio 10.75:1 H0015-24-S - 24T Pinion = ratio 8.95:1
H0015-21-S - 21T Pinion = ratio 10.25:1 H0015-26-S - 26T Pinion = ratio 8.25:1
H0015-xx-S is a motor pulley for 6mm motor shaft
Avaible also H0126-xx-S, motor pulley for 8mm motor shaft.
Jive 120 HV
YGE 160HV
21T
20T
21T
20T
22T
21T
21T
20T
Note: Although the Goblin can fly at high rpm, for safety reasons we suggest to not exceed 2000 rpm.
Some example configurations:
Quantum
4530-500
Pitch
18T
19T
20T
19T
SET RPM
Gov @80%
1820
SET RPM
21T
22T
Jive 120 HV
YGE 160HV
Ice 120 HV (V2)
Scorpion
HK 4525-520
Kontronik
Pyro
700-520
Scorpion
HK 5025-440
12S
5000/5500
3D
HARD 3D
3D
GENERAL
Gov
Pinion
ESC
Battery
12.5
12.5
12.5
Rev 01
RPM
Max
Performance
GOBLIN 770 CONFIGURATIONS
Motor
12S
5000/5500
14S
5000/5500
14S
5000/5500
Jive 120 HV
YGE 160HV
Ice 120 HV (V2)
SET RPM
Gov @80%
Gov @80%
1820
1850
1850
1820
1820
12.5
12.5
12.5
12.5
12.5
Quantum
4530-500
Scorpion
4530-500
Kontronik
Pyro
800-48
Scorpion
HK 5025-440
Quantum
4530-450
Scorpion
4530-450
Ice 120 HV (V2)
Kontronik
Pyro
800-48
Quantum
HK 5330-450
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
2000
2000
2100
2000
2000
2000
2000
2000
2050
2000
2100
SET RPM
SET RPM
SET RPM
SET RPM
Gov @75%
Gov @80%
Gov @80%
Gov @75%
Gov @80%
Gov @75%
Gov @75%
20T
20T
21T
Ice 120 HV (V2)
Ice 120 HV (V2)
Ice 120 HV (V2)
Jive 120 HV
YGE 160HV
Jive 120 HV
YGE 160HV
Jive 120 HV
YGE 160HV
YGE 160HV
KOSMIK 160
KOSMIK 160
YGE 160HV
KOSMIK 160
YGE 160HV
KOSMIK 160
YGE 160HV
Copyright@2012 - SAB Heli Division - All rights reserved
Page 28
Chapter 12, Installation Of The Motor
Motor Belt 240 GT3
(H308-S)
MOTOR BELT TENSION
*Assemble the motor and pinion to its mounting plate.
*Fit the motor assembly into position.
*Compress the springs by pushing the motor toward the main shaft.
*At maximum compression, temporarily tighten one of the slide screws.
*With the minimum centre distance it is easy to install the belt. First put the belt on the motor pinion.
*Then put the belt around the big pulley.
*Rotate the motor several times by hand.
*Release the screw that locks the slide.
*The springs keep the belt in tension.
*Help the springs by pulling the motor slightly.
*The belt must be very tight.
*Lock all screws.
Figure 1 shows the motor correctly wired. It is advisable to cover the wire joints between the motor and the ESC
with heat shrink tubing.
Motor
Assembly
Copyright@2012 - SAB Heli Division - All rights reserved
Page 29
Chapter 12, Installation Of The Motor
Finishing Washer M3
(H0007-S)
Safety Lock Tail Boom
(H0038-S)
The Socket Head Cap Screw
M3x16mm correctly positions
the boom assembly.
Socket Head Cap Screw
M3x8mm
....x1
Finishing Washer M3
Socket Head Cap Screw
M3x8mm
(HC050-S)
BOOM ASSEMBLY
*Insert the tail boom assembly making sure that the aluminum part of the tube touches the M3x16 screw.
*Lock the M8 nuts with the HA005 special tool supplied (Tray 2).
*Firmly lock the lateral M3 nuts.
*Assemble the H0038 carbon security plate .
*Connect the tail servo wire to the previously fitted extension lead.
....x1
Copyright@2012 - SAB Heli Division - All rights reserved
Page 30
Chapter 13, Installation Of The Boom
TAIL BELT TENSION
*Check the proper assembly of the tail boom.
*Check that the aluminum part of the tube is against the M3 stop screw.
*Loosen the tail group by loosening the 4 M3 screws.
*Install the belt onto the pulley, taking care to respect the direction of rotation (
figure 1
).
*Rotate the tail drive several times by hand.
*Load the spring by a rotation of
270°
the tensioning arm (
clockwise
)
*Tension the boom until the tensioning arm is aligned with the frame.
*Tighten the 4 screws.
*Check that the tail output shaft is perpendicular to the tube. (
figure 2
)
*In
figure 3,4,
5 you can see the three conditions, ok, too loose and too tight.
NOTE
. To disassemble the tail boom it is possible to remove the pulley H0016-S without loosening the tail unit.
Remove the locking screw and pull down.
Canopy
Red Canopy code: H0164-S - Yellow Canopy cod: H0148-S.
On the Goblin, the canopy touches the frame. To avoid triggering vibration, it is necessary to
attach an adhesive foam tape to the canopy
HA006
[
Bag 14
] (
figure 6
).
The canopy is locked at the point shown in
figure 8
and with two
H0036
kobs (both equipped
with OR
HA008
[
Bag 14
] (
figure 7
)). Confirm the canopy is secure prior to each flight.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 31
Chapter 13, Installation Of The Boom, Canopy
BATTERIES
The battery tray system in the Goblin 770 is simple, but very effective.
The battery should be attached to the tray (Part
H0149
) with heat shrink, tape or velcro.
You can optionally use the battery protection tray (Part
H0151
) see
Fig. 1, 2
.
Before permanently mounting the batteries onto the battery tray, check the ideal position for the best center of gravity.
Cut the heat shrink around the carbon fiber tray locking pins. Fig. 3.
Battery Pack:
Slide the tray until it locks into the CNC stopper.
Fig. 4, 5
.
Using the velcro straps, making sure that the two locking pins are stopped against the frame spacer
(Part1#
H0003
and #
H0151
)
Fig.6, 7
.
A
DETAIL A
SCALE 1 : 2.5
B
DETAIL B
SCALE 1.5 : 1
Battery Plate
(H0149-S)
Cylinder M2.5
(H0151-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Flat Head Cap Screw
M2.5x5mm
......x2
Copyright@2012 - SAB Heli Division - All rights reserved
Page 32
Chapter 14, Battery
OPERATIONS BEFORE FLIGHT
*Set up the remote control and the flybarless system with utmost care.
*It is advisable to test the correct settings of the remote and flybarless system without main blades or tail blades fitted.
*Check that all wiring is isolated from the carbon/aluminum parts. It is good practice to protect them at the points where
they are at most risk.
*Be sure of the gear ratio, verifying carefully the motor pulley in use. The forces acting on the mechanics increase
enormously with increasing of rpm. Although the Goblin can fly at high rpm, for safety reasons we suggest to not exceed
2000 rpm.
*Check the correct tension of the tail belt through the belt tensioner.
*Fit the main blades and tail blades. (Fig.1 and Fig.2)
*Please make sure the main blades are tight on the blade grips, you should be able to violently jerk the head in both
directions and the blades should not fold. Failure to tighten the blades properly can result in a boom strike.
To fold the blades for storage, it is advisable to loosen them.
*Check the collective and cyclic pitch. For 3D flight, set about +/- 12°-13°.
*It is important to check the correct tracking of the main blades.
*On the Goblin, in order to correct the tracking, adjust the main link rod as shown in figure 3. This is provided with a right/left
thread system that allows continuous fine adjustments of the length of the control rod; for this adjustment it is not necessary
to detach the ball link.
*Perform the first flight at a low headspeed, 1600 RPM.
After this first flight, do a general check of the helicopter. Verify that all screws are correctly tightened.
A
B
DETAIL A
SCALE 1 : 7
H0158
DETAIL B
SCALE 1 : 3.5
IN FLIGHT
During its first flights the Goblin has to be “run in”.
The Dampener system, the main gear, the uniball and other parts must undergo some slight wear to operate smoothly. It is likely that during
the very first flights the model may exhibit a swaying phenomena, particularly at low head speed.
This phenomena disappears after a few flights.
If you want to fly in a generic way, using both low headspeed and high headspeed, the standard setting is the best compromise.
However, if you prefer flying at low speed [< 18
00
rpm], for best results we recommend changing the tail pulley for a smaller
one to increase tail rotor rpm. In this way, you will have extremely precise tail control even at low RPM. This pulley is available
in the upgrade list [
H0154-S
].
Goblin 770 uses the HPS head.
The dampening system of this head allows for a wide range of head speeds to be used without sacrificing safety.
The dampers are composed of an o-ring and a technopolymer damper that defines the maximum possible movement of the spindle.
The model response with change based on the preload, less preload (less shims) will allow for a softer feel and lower head speed, a high
preload is used for hard 3D flight.
To increase the preload, you can add an additional 0.2mm shim on each side, to decrease the repload, you can remove a 0.2mm shim on each
side. It is important that the blade grips do not have the axial play so you must always keep the 1mm shim on each side regardless.
HC116
HC218
HC074
HC206
Copyright@2012 - SAB Heli Division - All rights reserved
Page 33
Chapter 15, In Flight
MAINTENANCE
*On the Goblin, areas to look for wear include:
* Motor belt
* Tail belt
* Damper
* Main gear and pinion
The lifespan of these components varies according to the type of flying. On average it is recommended to replace
these special parts every
100
flights.
*The head tends to lose rigidity after a while. Check this condition every
20
flights. Preloading with precision shim washers,
it is possible to vary the rigidity of the head.
*Check all uniballs often.
*The most stressed bearings are definitely those of the tail shaft. Check them frequently.
All other parts are not particularly subject to wear.
*Periodically lubricate the tail slide movement and its linkages as well as the swashplate movement and its linkages.
*Lubricate the main gear with Tri-Flow Synthetic grease, even though the gear is made of technopolymer,
a high mineral based filler, it still requires some lubrication.
*Check the screws that are highlighted in the following images frequently, make sure you remain tight (
fig.1
and
fig.2
).
*To ensure safety you should do a general inspection of the helicopter after each flight. You should check:
* The maintenance of proper belt tension.
* The proper isolation of wires from the carbon and aluminum parts.
* That all screws remain tight.
A
B
DETAIL A
SCALE 1 : 2.5
DETAIL B
SCALE 1 : 1.6
Copyright@2012 - SAB Heli Division - All rights reserved
Page 34
Chapter 16, Maintenance
4
2
5
3
7
3
7
8
9
7
7
6
7
7
7
7
1
15
21
22
21
11
21
21
18
18
18
20
19
13
18
16
16
10
14
10
18
21
21
18
18
18
17
22
12
21
24
25
Main Frame
POS
COD
Name
Specification
Quantity
1
H0145
Main Frames
Carbon Fiber
2
2
H0002
Battery Tray Carbon Fiber
1
3
H0003
Frame Spacers
Aluminum
3
4
H0004
ESC Support
Aluminum
1
5
H0005
Landing Gear Supports
Aluminum
2
6
H0106
Yellow Landing Gears
Carbon Fiber
2
H0162
Red Landing Gears
Carbon Fiber
2
7
H0007
Finishing Washers M3
Aluminum
12
8
H0008
Canopy Positioners
Aluminum
2
9
H0036
Canopy Lockings
Aluminum
2
10
H0039 Landing Gear Protection
Plastic
4
11
H0153
Battery Support
Carbon Fiber
1
12
H0155
Battery Protection
Carbon Fiber
1
Main Frame
POS
COD
Name
Specification
Quantity
13
H0074
Landing Gear Struts
Carbon Fiber
4
14
HA008
Canopy ORs O-ring
Oring 3030
2
15
HA010
Cable Pass
16 x
24 x 2mm
1
16
HC018
Socket Head Cap Screws
M2.5 x 6mm
4
17
HC020
Socket Head Cap Screws
M2.5 x 8mm
2
18
HC056
Socket Head Cap Screws
M3 x 10mm
16
19
HC096
Button Head Cap Screws
M4 x 6mm
4
20
HC100
Button Head Cap Screws
M4 x 10mm
4
21
HC128
Flat Head Cap Screws
M2.5 x 5mm
12
22
H0149
Battery Plate
Carbon Fiber
1
23
H0150
Stop Battery Plate
Plastic
1
24
H0151
Cylinder M2.5
Aluminum
2
25
H0157
Canopy Positioners
Plastics
2
Copyright@2012 - SAB Heli Division - All rights reserved
Page 35
Chapter 17, Exploded view, Carbon Frame
Servo
Assembly 1
Servo
Assembly 2
Servo
Assembly 3
12
1
3
30
22
13
32
34
7
20
2
23
31
34
35
32
29
24
33
48
5
15
6
26
21
11
25
19
18
17
36
9
4
16
10
8
16
37
43
42
40
39
41
27
38
Swashplate Set - H0023
Servo Assembly 1, 2, 3
44
10
11
14
46
28
49
45
47
50
Head System
POS
COD
Name
Specification
Quantity
1
H0023
Swashplate Set
1
2
H0025
Locking Nut Main Blade Grips
Aluminum
4
3
H0144
Damper Derlin
2
4
H0031
Uniball Spacers
Aluminum
3
5
H0205
Unibal Radius Arms
Plastic
2
6
H0132
Radius Arms Aluminum
2
7
H0034
Main Blade Grips
Aluminum
2
8
H0063
Uniball
M3 x 4
5 H18
1
9
H0064
Uniballs
M2.5
5 H6
3
10
H0065
Uniballs
M3 x 4
5 H3
8
11
H0066
Plastic Ball Linkages
Plastic
8
12
H0075
Servo Spacers
Carbon Fiber
6
13
H0079
Spindle
Carbon Steel
1
14
H0135
Center Hub
Aluminum
1
15
H0136
Blade Grip Arms
Aluminum
2
16
HC008
Socket Head Cap Screws
M2 x 8mm
7
17
HC020
Socket Head Cap Screws
M2.5 x 8mm
3
18
HC026
Socket Head Cap Screws
M2.5 x 12mm
9
19
HC044
Socket Head Cap Screws
M3 x 6mm
3
20
HC056
Socket Head Cap Screws
M3 x 10mm
2
21
HC062
Socket Head Cap Screws
M3 x 12mm
2
22
HC111
Socket Head Cap Screw Shouldered
M4 x 24mm
1
23
HC116
Socket Head Cap Screw Shouldereds
M5 x 34mm
2
24
HC122
Button Head Cap Screws
M6 x 10mm
2
25
HC242
Threaded Rods
M2.5 x 40mm
3
Head System
POS
COD
Name
Specification
Quantity
26
H0137
Linkages
M2.5 x 48mm
2
27
HC170
Washers
2 x
5 x 0.5mm
3
28
HC176
Washers
3 x
4 x 0.5mm
2
29
HC194
Washers
6 x
14 x 1.5mm
2
30
HC212
Metric Hex Nylon Nut
M4 H5
1
31
HC218
Metric Hex Nylon Nuts
M5 H4.8
2
32
HC230
Washers
10 x
16 x 1mm
4
33
HC402
Flanged Bearings
3 x
7 x 3mm
4
34
HC422
Bearings
10 x
19 x 5mm
4
35
HC438
Thrust Bearings
10 x
18 x 5.5mm
2
36
HC232
Washers
10 x
16 x 0.2mm
2
37
H0023-01
Swashplate 01
1
38
H0023-02
Swashplate 02
1
39
H0023-03
Swashplate 03
1
40
H0023-04
Swashplate 04
2
41
H0023-05
Swashplate 05
1
42
HC002
Socket Head Cap Screws
M2 x 5mm
3
43
HC430
Bearing Rads
30 x
37 x 4mm
2
44
HA024
Oring
3050
2
45
H0235
Spacer Arm
2.5 x
4 x 6.3mm
2
46
H0134
Spacer Arm
3 x
5 x 2.7mm
2
47
HC032
Socket Head Cap Screws
M2.5 x 18mm
2
48
HC068
Socket Head Cap Screws
M3 x 16mm
2
49
HC400
Flanged Bearings
2.5 x
6 x 2.5mm
4
50
H0158
Blade Washers
5 x
24 x 1mm
4
Copyright@2012 - SAB Heli Division - All rights reserved
Page 37
Chapter 17, Exploded view, Head System
37
8
1
41
41
49
7
4
6
42
56
25
53
43
49
15
14
46
12
23
22
52
44
52
47
35
3
26
20
36
19
18
30
34
55
16
2
17
40
40
46
11
24
38
54
9
58
13
31
32
49
31
49
57
37
59
21
34
26
51
50
28
51
60
28
29
27
45
33
48
TAIL SYSTEM
POS
COD
Name
Specification
Quantity
1
H0007
Finishing Washer M3
Aluminum
4
2
H0029
Spacer
8.1 x
9.2 x 3.2mm
1
3
H0031
Uniball Spacer
Aluminum
1
4
H0147
Yellow Tail Boom
Carbon Fiber
1
H0163
Red Tail Boom
Carbon Fiber
1
6
H0040
Tail Servo Locks
Plastic
2
7
H0041
Locking Element Tails
Carbon Fiber
2
8
H0045
Linkage Tail Support
Plastic
1
9
H0046
Yellow Vertical Fin
Carbon fiber
1
H0117
Red Vertical Fin
Carbon fiber
1
11
H0047
Tail Side Plate
Carbon fiber
1
12
H0048
Tail Rotor Shaft
Carbon Steel
1
13
H0155
Tail Pulley
25T
1
14
H0051
Tail Rotor Hub
Carbon Steel
1
15
H0052
Tail Blade Grips
Aluminum
2
16
H0053
Tail Pitch Slider 01
1
17
H0054
Tail Pitch Slider 02
1
18
H0055
Tail Pitch Slider 03
1
19
H0056
Grip Links
2
20
H0057
Main Grip Link Bushs
2
21
H0058
Bell Crank Base
Aluminum
1
22
H0059
Bell Crank Lever
Aluminum
1
23
H0060
Spacer
3 x
4 x 9.6mm
1
24
H0061
Tail Case Spacers
Aluminum
4
25
H0062
Spacers
7 x
9 x 0.5mm
2
26
H0064
Uniballs
M2.5
5 H6
2
27
H0065
Uniball
M3 x 4
5 H3
1
28
H0066
Plastic Ball Links
Plastic
2
29
H0072
Bush Bell Crank
1
30
H0076
Grip Link Bushs
2
31
H0078
Washers
3.1 x
12 x 1.8mm
2
TAIL SYSTEM
POS
COD
Name
Specification
Quantity
32
H0082
Boom Spacers
Aluminum
2
33
HC002
Socket Head Cap Screws
M2 x 5mm
6
34
HC004
Socket Head Cap Screws
M2 x 6mm
3
35
HC008
Socket Head Cap Screw
M2 x 8mm
1
36
HC014
Socket Head Cap Screws
M2 x 12mm
2
37
HC018
Socket Head Cap Screws
M2.5 x 6mm
2
38
HC020
Socket Head Cap Screws
M2.5 x 8mm
2
39
HC026
Socket Head Cap Screws
M2.5 x 12mm
4
40
HC050
Socket Head Cap Screws
M3 x 8mm
8
41
HC062
Socket Head Cap Screws
M3 x 12mm
4
42
HC068
Socket Head Cap Screws
M3 x 16mm
2
43
HC074
Socket Head Cap Screw Shouldereds
M3 x 16mm
2
44
HC086
Socket Head Cap Screw
M3 x 22mm
1
45
HC150
Set Screws
M3 x 20mm
3
46
HC152
Set Screws
M4 x 4mm
2
47
HC176
Washer
3 x
4 x 0.5mm
1
48
HC181
Washers
3.3 x
7 x 1mm
2
49
HC206
Metric Hex Nylon Nuts
M3
8
50
HC238
Carbon Rod
2.5 x
4 x 752mm
1
51
HC242
Threaded Rods
M2.5 x 40mm
2
52
HC402
Flanged Bearings
3 x
7 x 3mm
2
53
HC406
Bearings
5 x
9 x 3mm
4
54
HC414
Flanged Bearings
6 x
13 x 5mm
2
55
HC418
Flanged Bearings
8 x
12 x 3.5mm
2
56
HC434
Thrust Bearings
4 x
9 x 4mm
2
57
HA015
Double-Sided Tapes
2
58
HC325
Belt Gates
2160-3MGT-06
1
59
H0075
Servo Spacers
Carbon Fiber
2
60
HC044
Screw supplied with Servo
M3 x 6mm
1
Copyright@2012 - SAB Heli Division - All rights reserved
Page 38
Chapter 17, Exploded view, Tail System
- 1 x Main Structure.
- 1 x Servo Support.
- 4 x Sliding Landing Gears.
- 4 x Socket Head Cap Screws
M2.5x6mm.
Sliding Landing Gear
[H0039-S]
- 1 x CF Battery Tray.
- 6 x Flat Head Cap Screws M2.5x5mm.
Battery Tray
[H0002-S]
Frame Spacer
[H0003-S]
- 1 x ESC Support.
- 2 x Flat Head Cap Screws M2.5x5mm.
ESC Support
[H0004-S]
- 10 x Finishing Washers M3.
Finishing Washer M3
[H0007-S]
Canopy Positioner
[H0008-S]
Main Structure
[H0009-S]
Servo Support
[H0010-S]
68T Main Gear
[H0012-S]
- 1 x 18T Pulley 6mm.
- 2 x Set Screws M4x4.
18T Pulley
[H0015-18-S]
19T Pulley
[H0015-19-S]
20T Pulley
[H0015-20-S]
- 1 x 20T Pulley 6mm.
- 2 x Set Screws M4x4.
21T Pulley
[H0015-21-S]
- 1 x 21T Pulley 6mm.
- 2 x Set Screws M4x4.
23T Pulley
[H0015-23-S]
- 1 x 23T Pulley 6mm.
- 2 x Set Screws M4x4.
24T Pulley
[H0015-24-S]
- 1 x 24T Pulley 6mm.
- 2 x Set Screws M4x4.
26T Pulley
[H0015-26-S]
- 1 x 26T Pulley 6mm.
- 2 x Set Screws M4x4.
Chapter 18, Spare Parts
- 1 x 68T Main Gear .
- 1 x Socket Head Cap Screw
Shouldered M4x24mm.
- 1 x Metric Hex Nylon Nut M4 H5.
- 1 x 22T Pulley 6mm.
- 2 x Set Screws M4x4.
- 1 x 19T Pulley 6mm.
- 2 x Set Screws M4x4.
- 3 x Frame Spacers.
Landing Gear Support
[H0005-S]
- 1 x Landing Gear Support.
- 2 x Canopy Positioners.
22T Pulley
[H0015-22-S]
- 4 x Columns.
Column
[H0018-S]
- 1 x Swashplate Assembly.
- 2 x Bearings 30x
37x4mm.
- 6 x Uniballs M3x4
5 H3.
- 1 x Uniball M3x4
5 H18.
- 3 x Socket Head Cap Screws M2x5mm.
- 4 x Socket Head Cap Screws M2x8mm.
Swashplate
[H0023-S]
- 1 x Bearing Support.
- 1 x Bearing
12x
24x6mm.
- 3 x Flat Head Cap Screws
M2.5x5mm.
Bearing Support
[H0024-S]
- 1 x Blade Grip.
- 2 x Bush Blade Grips.
Blade Grip
[H0034-S]
- 2 x Canopy Lockings.
- 2 x Canopy ORs.
Canopy Locking
[H0036-S]
- 1 x Safety Lock Tail Boom.
- 1 x Finishing Washer M3.
- 1 x Socket Head Cap Screw M3x8mm.
Safety Lock Tail Boom
[H0038-S]
- 2 x Tail Servo Locks.
- 2 x Servo Spacers.
- 4 x Socket Head Cap Screws
M2.5x12mm.
Tail Servo Lock
[H0040-S]
Copyright@2012 - SAB Heli Division - All rights reserved
Page 39
- 10 x Washers
3.1x
12x1.8mm.
Washer
3.1x
12x1.8mm
[H0078-S]
- 2 x Locking Element Tails.
- 4 x Metric Hex Nylon Nuts M3.
- 2 x Double Sided Tapes.
Locking Element Tail
[H0041-S]
Battery Protection
[H0042-S]
Spacer Flybarless
[H0043-S]
- 1 x Vertical Fin.
- 2 x Socket Head Cap Screws
M3x12mm.
- 2 x Finishing Washers M3.
Vertical Fin
[H0046-S]
- 2 x Tail Case Spacers.
- 4 x Socket Head Cap Screws
M3x8mm.
Spacer
7x
9x0.5mm
[H0062-S]
- 1 x Linkage Tail Support.
- 2 x Socket Head Cap Screws
M2.5x6mm.
Linkage Tail Support
[H0045-S]
Tail Case Spacer
[H0061-S]
Uniball M3x4
5H3
[H0065-S]
- 1 x Battery Protection.
- 3 x Spacer Flybarless.
- 1 x Supporto Flybarless.
- 1 x Flat Head Cap Screw M3x8mm.
- 5 x Socket Head Cap Screws M3x6mm.
- 1 x Tail Side Plate.
- 2 x Socket Head Cap Screws
M3x12mm.
- 2 x Finishing Washers M3.
Tail Side Plate
[H0047-S]
- 2 x Antenna Guide.
- 2 x Button Head Cap
Screws M3x4mm.
Antenna Guide
[H0050-S]
- 1 x Tail Rotor Hub.
- 1 x Set Screw M4x4mm.
- 2 x Socket Head Cap
Screws M3x16mm.
Tail Rotor Hub
[H0051-S]
- 2 x Tail Blade Grips.
- 2 x Socket Head Cap Screws
M3x16mm.
- 4 x Bearings
5x
9x3mm.
Tail Blade Grip
[H0052-S]
- 1 x Bell Crank Base.
Bell Crank Base
[H0058-S]
- 2 x Grips Link.
- 2 x Main Grip Link Bush.
- 2 x Grip Link Bush.
- 2 x Socket Head Cap Screws
M2x12mm.
- 2 x Socket Head Cap Screws
M2x6mm.
Grip Link
[H0056-S]
Tail Pitch Slider
[H0053-S]
- 1 x Tail Pitch Slider 01.
- 1 x Tail Pitch Slider 02.
- 1 x Tail Pitch Slider 03.
- 1 x Spacer
8x
9x3.2mm.
- 1 x Uniball M3x4
5H3.
- 2 x Flanged Bearings
8x
12x3.5mm
- 1 x Bell Crank Lever.
- 1 x Bush Bell Crank.
- 1 x Washer
3x
4x0.5mm.
- 1 x Spacer
3x
4x9.6mm.
- 1 x Socket Head Cap Screw M3x22mm.
- 2 x Flanged Bearings
3x
7x3mm.
Bell Crank Lever
[H0059-S]
- 4 x Spacers
3x
4x0.5mm
- 1 x Uniball M3x4
5H18
Uniball M3x4
5H18
[H0063-S]
- 5 x Uniballs M2
5H6.
- 5 x Uniball Spacers.
- 5 x Socket Head Cap Screws M2x8mm.
- 5 x Socket Head Cap Screws M2x6mm.
Uniball M2
5H6
[H0064-S]
- 5 x Uniballs M3x4
5H3.5.
- 10 x Plastic Ball Links
Plastic Ball Link
[H0066-S]
- 1 x Belt Tensioner Support.
- 1 x Tail Belt Idler.
- 1 x Belt Tensioner Arm.
- 2 x Flanged Bearings
3x
7x3mm.
- 2 x Flanged Bearings
5x
9x3mm.
- 1 x Socket Head Cap Screw M3x50mm.
- 1 x Washer
3x
4x0.5mm.
- 1 x Socket Head Cap Screw M3x12mm.
- 2 x Washers
3.2x
6x0.5mm.
- 1 x Button Head Cap Screw M3x4mm.
- 1 x Spring De8/df0.5/LL8.
Belt Tensioner Support
[H0070-S]
- 4 x Landing Gear Struts.
- 4 x Button Head Cap Screws
M4x6mm.
- 4 x Button Head Cap Screws
M4x10mm.
Landing Gear Struts
[H0074-S]
-10 x Servo Spacers.
Servo Spacer
[H0075-S]
- 1 x Spindle.
- 2 x Button Head Cap Screws M6x10mm.
- 2 x Washers
6x
14x1mm.
Spindle
[H0079-S]
Copyright@2012 - SAB Heli Division - All rights reserved
Page 40
Chapter 18, Spare Parts
- 1 x 23T Pulley 8mm
- 2 x Set Screws M4x4mm.
Tail boom Support
[H0082-S]
37T Pulley
[H0101-S]
19T Pulley
[H0126-19-S]
20T Pulley
[H0126-20-S]
- 1 x Long Main Shaft.
- 1 x Socket Head Cap Screw M4x22mm.
- 1 x Socket Head Cap Screw Shouldered
M4x24mm.
- 3 x Metric Hex Nylon Nuts M4H5.
Long Main Shaft
[H0127-S]
- 1 x 37T Pulley.
- 1 x Socket Head Cap Screws M2.5x19mm.
- 1 x Hex Metric Nylon Nut M2.5H3.5.
- 1 x 19T Pulley 8mm.
- 2 x Set Screws M4x4mm.
21T Pulley
[H0126-21-S]
22T Pulley
[H0126-22-S]
- 2 x Tail Boom Support.
- 3x Set Screws M3x20mm.
24T Pulley
[H0126-24-S]
- 1 x 60T Pulley .
- 2 x Bush One Ways.
- 2 x Bearings 10x15x4mm
- 1 x One Way Bearing 10x14x12mm.
60T Pulley
[H0104-S]
- 1 x CF Low Landing Gear Yellow.
Low Landing Gear Yellow
[H0106-S]
- 1 x Red Vertical Fin.
- 2 x Socket Head Cap Screws M3x12mm.
- 2 x Finishing Washers M3.
Red Vertical Fin
[H0117-S]
- 1 x M4 Locking Collar.
- 1 x Socket Head Cap Screw M4x22mm.
- 1 x Metric Hex Nylon Nut M4 H5.
M4 Locking Collar
[H0121-S]
- 1 x 20T Pulley 8mm.
- 2 x Set Screws M4x4mm.
- 1 x 21T Pulley 8mm.
- 2 x Set Screws M4x4mm.
- 1 x 22T Pulley 8mm.
- 2 x Set Screws M4x4mm.
23T Pulley
[H0126-23-S]
- 1 x 23T Pulley 8mm.
- 2 x Set Screws M4x4mm.
-2 x Radius Arms.
-2 x Spacer Arm
3x
5x2.7mm.
-2 x Spacer Arm
2.5x
4x6.3mm.
-2 x Uniball Radius Arms.
-2 x Socket Head Cap Screws
M3x16mm.
-2 x Socket Head Cap
Screws M2.5x18mm.
-2 x Washers
3x
4x0.5mm.
-2 x Flanged Bearings
2.5x
6x2.5mm.
-2 x Flanged Bearings
3x
7x3mm.
Radius Arm
[H0132-S]
-1 x Center Hub.
-2 x Socket Head Cap Screws
M3x12mm.
-1 x Socket Head Cap Screw
Shouldered M4x24mm.
-1 x Metric Hex Nylon Nut
M4 H5.
Center Hub
[H0135-S]
-2 x Blade Grip Arms.
-2 x Uniballs M3x4
5H3.
-2 x Socket Head Cap Screws
M3x10mm.
Blade Grip Arm
[H0136-S]
-2 x Linkages M2.5x48mm.
-4 x Plastic Ball Links.
Linkage
[H0137-S]
- 2 x Finishing Washers M3.
- 2 x Socket Head Cap Screws
M3x10mm.
- 2 x Metric Hex Nylon Nut M3 H4.
- 2 x Springs de 5.8/ df0.5 / LL9.
- 2 x Springs de 3/ df0.5 / LL12.
Motor Support
[H0143-S]
- 1 x Bearing 3
Support.
- 1 x Motor Support.
- 1 x Flanged Bearing
6x
13x5mm.
- 2 x Socket Head Cap Screws M3x8mm.
- 2 x Set Screws M5x20mm.
- 2 x Washers
5.3x
15x1mm.
- 2 x Metric Hex Nylon Nuts M5H4.8.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 41
Chapter 18, Spare Parts
Main Frame
[H0145-S]
Yellow Tail Boom
[H0147-S]
ESC Support
[H0153-S]
24T Pulley
[H0154-S]
- 1 x Secondary Shaft M3.
- 1 x Socket Head Cap Screw
M2.5x19mm.
- 1 x Socket Head Cap Screw
M3x20mm.
- 1 x Metric Hex Nylon Nut M2.5 H3.5.
- 1 x Metric Hex Nylon Nut M3 H4.
- 4 x Blade Spacer.
Blade Spacer
[H0158-S]
- 1 x CF ESC Support.
- 6 x Flat Head Cap Screws
M2.5x5mm.
- 1 x 24T Tail Pulley.
- 1 x Set Screws M4x4mm.
Secondary Shaft M3
[H0157-S]
Canopy
Positioner
[H0159-S]
- 1 x CF
Red Landing Gear Low Profile.
Red Landing Gear Low Profile
[H0162-S]
ESC Heatsink
[H0165-S]
- 1 x ESC Heatsink.
- 4 x Socket Head Cap Screws
M3x6mm.
- 4 x Set Screws M3x20mm.
- 4 x Metric Hex Nylon Nuts M3 H4.
- 12 x Washers
3.2x
6x.05mm.
- 3 x Set Screws M3x20mm.
- 2 x Washers
3.1x
12x1.8mm.
- 2 x Metric Hex Nylon Nuts M3 H4.
- 2 x Vite Nylon Esa M8x14mm.
- 2 x Metric Hex Nuts M8 H6.5.
- 2 x Double Sided Tapes.
- 1 x Yellow Tail Boom.
- 1 x Tail Boom Interface.
- 1 x Locking Interface.
- 2 x Tube Spacers.
- 2 x Locking Element Tails.
- 4 x Button Head Cap Screws M4x8mm.
Damper Derlin
[H0144-S]
-2 x Damper Derlin.
-2 x Washers
10x
16x1mm.
-4 x Washers
10x
16x0.2mm.
-4 x Orings 3050.
-1 x CF Main Frame.
Yellow / Blue Canopy 770
[H0148-S]
- 1 x Yellow / Blue Canopy 770
- 1 x Canopy Mouse.
- 2 x Canopy Grommet.
Battery Tray
[H0149-S]
Stop Battery Tray
[H0150-S]
- 1 x Stop Battery Tray.
- 2 x Socket Head Cap
Screw M2.5x8mm.
Anti-rotation Guide
[H0152-S]
- 1 x Anti-rotation Guide.
- 1 x Socket Head Cap Screw M3x8mm.
- 1 x Finishing Washer M3.
- 1 x Battery Plate.
- 1 x Battery Protection.
- 2 x Cylinder M2.5.
- 2 x Flat Head Cap Screw M2.5x5mm
- 1 x Heat Shrink.
- 1 x 25T Tail Pulley.
- 1 x Set Screws M4x4mm.
25T Pulley
[H0155-S]
19T Pinion
[H0156-S]
- 1 x 19T Pinion.
- 1 x Socket Head Cap Screw M3x20mm.
- 1 x Metric Hex Nylon Nut M3H4.
- 1 x Spacer Arm
3x
5x2.7mm.
- 2 x Canopy Positioner.
- 2 x Socket Head Cap Screw
M3x10mm.
Red Tail Boom
[H0163-S]
- 3 x Set Screws M3x20mm.
- 2 x Washers
3.1x
12x1.8mm.
- 2 x Metric Hex Nylon Nuts M3 H4.
- 2 x Vite Nylon Esa M8x14mm.
- 2 x Metric Hex Nuts M8 H6.5.
- 2 x Double Sided Tapes.
- 1 x Red Tail Boom.
- 1 x Tail Boom Interface.
- 1 x Locking Interface.
- 2 x Tube Spacers.
- 2 x Locking Element Tails.
- 4 x Button Head Cap Screws M4x8mm.
- 1 x Red Canopy 770
- 1 x Canopy Mouse.
- 2 x Canopy Grommet.
Red Canopy 770
[H0164-S]
Copyright@2012 - SAB Heli Division - All rights reserved
Page 42
Chapter 18, Spare Parts
-5 x Socket Head Cap
Screws M2x5mm.
[HC002-S]
[HC004-S]
-5 x Socket Head Cap
Screws M2x6mm.
[HC008-S]
-5 x Socket Head Cap
Screws M2x8mm.
[HC014-S]
-5 x Socket Head Cap
Screws M2x12mm.
[HC018-S]
-5 x Socket Head Cap
Screws M2.5x6mm.
[HC020-S]
-5 x Socket Head Cap
Screws M2.5x8mm.
[HC026-S]
-5 x Socket Head Cap
Screws M2.5x12mm.
[HC033-S]
[HC038-S]
- 5 x Button Head Cap
Screws M3x4mm.
[HC044-S] [HC050-S]
[HC056-S]
[HC062-S]
-5 x Socket Head Cap
Screws M3x12mm.
[HC068-S]
-5 x Socket Head Cap
Screws M3x16mm.
[HC074-S]
-2 x Socket Head Cap Screw
Shouldereds M3x16mm.
-2 x Metric Hex Nylon Nuts
M3H4.
[HC083-S] [HC086-S]
-5 x Socket Head Cap
Screws M3x22mm.
[HC096-S] [HC098-S]
-5 x Button Head Cap
Screws M4x8mm.
[HC100-S]
-5 x Button Head Cap
Screws M4x10mm.
[HC104-S]
-5 x Socket Head Cap
Screws M4x22mm.
[HC110-S]
-5 x Socket Head Cap
Screw s M4x25mm.
[HC116-S]
- 2xSocket Head Cap Screw
Shouldereds M5x35mm.
- 2xMetric Hex Nylon Nuts
M5H4.8.
[HC122-S] [HC128-S] [HC134-S] [HC140-S]
- 5 x Set Screws
M2.5x20mm.
[HC150-S]
- 5 x Set Screws
M3x20mm.
[HC152-S] [HC164-S]
- 4 x Vite Nylon Esa
Cap M8x14mm.
[HC170-S]
[HC176-S]
- 5 x Washers
3x
4x0.5mm.
[HC180-S]
- 10 x Washers
3.3x
6x0.5mm.
[HC181-S] [HC188-S]
[HC194-S]
- 10 x Washers
3.3x
9x0.8mm.
- 5 x Washers
5.3x
15x1mm.
[HC200-S] [HC206-S]
- 10 x Metric Hex Nylon
Nuts M2.5H3.5.
- 10 x Metric Hex Nylon
Nuts M3H4.
[HC212-S]
[HC218-S]
[HC224-S] [HC230-S] [HC232-S]
- 5 x Washers
6x
14x1.5mm.
- 10 x Metric Hex Nylon
Nuts M4 H5.
- 5 x Metric Hex Nylon
Nuts M5 H4.8.
- 4 x Metric Hex Nuts
M8 H6.5.
- 5 x Shim Washers
10x
16x1mm.
- 5 x Shim Washers
10x
16x0.2mm.
[HC158-S]
-5 x Button Head Cap
Screws M6x10mm.
-5 x Socket Head Cap
Screws M3x8mm.
-5 x Flat Head Cap
Screws M2.5x5mm.
- 5 x Set Screws
M4x4mm.
- 5 x Set Screws
M5x20mm.
-5 x Socket Head Cap Screw
Shouldereds M3x20mm.
[HC082-S]
- 5 x Socket Head Cap Screw
Shouldereds M2.5x19mm.
-5 x Socket Head Cap
Screws M3x6mm.
-5 x Socket Head Cap
Screws M3x10mm.
[HC080-S]
-5 x Socket Head Cap
Screws M3x20mm.
-2xSocket Head Cap Screw
Shouldereds M3x50mm.
[HC092-S]
-5 x Socket Head Cap Screw
Shouldereds M3x22mm.
-5 x Button Head Cap
Screws M4x6mm.
[HC090-S]
-5xSocket Head Cap Screw
Shouldereds M3x30mm.
[HC146-S]
- 5 x Set Screws
M2.5x15mm.
[HC111-S]
-5xSocket Head Cap Screw
Shouldereds M4x24mm.
- 5 x Washers
2.2x
5x0.3mm.
-5 x Flat Head Cap
Screws M3x8mm.
- 5 x Shim Washers
10x
16x0.1mm.
[HC234-S]
Copyright@2012 - SAB Heli Division - All rights reserved
Page 43
Chapter 18, Spare Parts
[HC420-S]
- 2 x Bearings
10x
15x4mm.
- 4 x Flanged Bearings
2.5x
6x2.6mm.
[HC238-S]
- 1 x Carbon Rod
2.5 x
4 x752mm.
- 2 x Plastic Ball Links.
- 2 x Threaded Rods M2.5x40mm.
[HC325-S]
- 1 x Belt Gates
2160-3MGT-06.
- 1 x Belt Gates 240-3MGT-13.
[HC406-S]
- 4 x Flanged Bearings
3x
7x3mm.
[HC410-S] [HC414-S] [HC418-S]
[HC422-S] [HC426-S] [HC430-S]
[HC434-S]
[HC438-S]
[HC442-S]
[HC308-S]
[HC402-S]
[HC315-S]
- 4 x Bearings
5x
9x3mm.
- 4 x Flanged Bearings
5x
9x3mm.
- 2 x Flanged Bearings
6x
13x5mm.
- 2 x Flanged Bearings
8x
12x3.5mm.
- 2 x Bearings
12x
24x6mm.
- 2 x Bearing Rads
30x
37x4mm.
- 2 x Thrust Bearings
4x
9x4mm.
- 2 x Thrust Bearings
10x
18x5.5mm.
- 1 x One Way Bearing
10x
14x12mm.
[HA001-S] [HA002-S]
[HA006-S]
- 1 x Foam Blade Holder.
- 2 x Hex Wrenches
2.5mm.
[HA008-S]
[HA0010-S]
[HA012-S]
- 5 x Canopy ORs.
- 2 x Cable Pass.
- 8 x Battery ORs.
- 1 x Canopy Mousse 80cm.
- White Tail Blades 115mm
- 4 x Bearings
10x
19x5mm.
[HA016-S]
- 2 x Springs
de 5.8/df 0.3/LL9.
- 1 x Spring
de 8/df 0.5/LL8.
- 2 x Springs
de 3/df 0.5/LL12.
[HC400-S]
[HA111-S]
- 4 x Canopy Grommets.
- 1 x Plastic Wrench
Nut M8 & M6.
[HA024-S]
- 4 x Orings 3050.
[HA025-S]
- Straps Large Velcro.
[HA026-S]
- Heat Shrink
(4pcs 350mm.)
[HA903-S]
Manual Goblin770
[BW6115][BW2770]
- White Main Blades 770mm
[HC242-S]
- 3 x Threaded Rods
M2.5x40mm.
Copyright@2012 - SAB Heli Division - All rights reserved
Page 44
Chapter 18, Spare Parts
REV. 01 Copyright@2011 – SAB Teli division – All rights reserved
Manual Goblin 700
WWW.GOBLIN-HELICOPTER.COM
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw SAB Heli Division Goblin 770 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van SAB Heli Division Goblin 770 in de taal/talen: Engels als bijlage per email.

De handleiding is 66,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info