383096
15
Verklein
Vergroot
Pagina terug
1/142
Pagina verder
OPERATION
GENERAL CUTTING (Fig. 5)
Rest the front of the saw base on the workpiece and align
cutting edge of the blade with the line on your workpiece.
Make sure the power cord is out of the way of saw blade
and not in the line of cut. Start your saw and move it
forward on the work surface. Apply downward pressure to
keep the saw steady and only enough forward pressure
to keep the blade cutting.
DO NOT FORCE YOUR SAW
Forcing your saw may overheat the motor and
break saw blades.
ORBITAL MOTION (Fig. 5)
The blade of your saw cuts in orbital motion. This feature
is adjustable and provides faster and more efficient
cutting. With orbital motion the blade cuts through your
work in the upstroke but does not drag across your work
in the downstroke.
Higher settings (H) should be used when fast cutting
in soft material.
Lower (L) settings should be used when cutting
materials with more resistance.
STRAIGHT CUT (Fig. 5)
Astraight cut can be made by clamping a piece of wood or
straightedge to the workpiece and guiding the edge of your
saw against it. Make the cut from one direction only, do not
cut halfway to complete the cut from the opposite end.
SCROLL CUTTING (Fig. 6)
Scroll cuts can be made with your saw by guiding the
direction of the cut with applied pressure on the handle.
WARNING
Excessive side pressure to the blade could result in
broken blades or damage to the material being cut.
ANGLE CUTTING (Bevel Cutting) (Fig. 7)
Bevel cutting angles may be adjusted from 0° to 45° right
or left. Angles for cuts from 0° to 45° in 15° increments
are marked on a scale on both the left and right side of
the base.
The use of a protractor is recommended when accurate
cuts are required.
Adjusting the angle – EJS-600QEO only
Release the bevel lock lever (10) until the base can
be moved.
Slide base forward slightly to release the base from
the tab on the motor housing.
Align the mark on the base of the desired angle with
the edge of the motor housing.
Once the desired angle is reached, slide the base
back until the tab on the motor housing aligns with the
appropriate notch on the rear of the base.
Push the bevel lock lever back to secure the base.
Adjusting the angle – EJS-500QEO only
Loosen the base retaining screws with the wrench
(supplied) until the base can be moved.
Slide base forward slightly to release the base from
the tab on the motor housing.
Align the mark on the base of the desired angle with
the edge of the motor housing.
Once the desired angle is reached, slide the base
back until the tab on the motor housing aligns with the
appropriate notch on the rear of the base.
Re-tighten the base retaining screws with the wrench
(supplied) to secure the base.
TO MAKE A PLUNGE CUT (Fig. 8)
WARNING
To avoid loss of control, broken blades, or
damage to the material being cut, always use
extreme caution when making plunge cuts.
We do not recommend plunge cutting on
materials other than wood.
Mark the line of cut clearly on the workpiece.
Set the cutting angle at 0°.
Tilt your saw forward so that it rests on the front edge
of the base and blade will not come in contact with the
workpiece when the saw is turned on.
Make sure the blade is inside the area
to be cut.
Start your saw by using high speed and slowly lower
the blade into the workpiece until the blade cuts
through the wood.
Continue lowering the blade into the workpiece until
the base rests flat on the work surface, then move the
saw forward to complete the cut.
Use only the 7 teeth per inch blade for this type of cut.
11
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
EJS-500-600QEO_20 lgs 22/01/06 17:49 Page 11
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ryobi ejs 500 qeo bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ryobi ejs 500 qeo in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info