733430
19
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
17
2
3
1
12
1
2
3
4
2
1
65
x4x4
30 sec
RUN
1
2
13 14
15 16 17 18
1
2
7
1
2
8
9
2
1
3
1/4-20 x 1.85 in
4
GETTING STARTED GETTING STARTED GETTING STARTED GETTING STARTED
11
1
2
3
4
5
1/4-20 x 1.85 in
1/4-20 x 2.1 in
3
1. Turn the on/off switch to the ON position. 2. Turn the fuel
valve to the ON (horizontal) position.
Pull choke to START position.
Grasp the starter grip and pull slowly until you feel the
resistance. Give the starter grip a short, brisk pull to start
the engine.
Let the engine run for several seconds, then gradually slide
the choker lever fully toward the RUN position.
Push choke into the RUN position. 1. Push up the lock out until it clicks into the slot. 2. Squeeze
the trigger to operate the high pressure cleaner.
1. Place hose storage onto handle. 2. Align holes in the hose storage with holes in the handle. Insert screw (1/4-20 x 1.85
in.) through holes in the left side. Insert screw (1/4-20 x 2.1 in.) through holes in the right side. 3. Place nut onto the screw
(left) and tighten. 4. Place trigger handle holder onto the screw (right). 5. Place washer and nut onto the screw and tighten.
1. Place spray wand holder onto frame. 2. Align holes in
both spray wand holder and frame. Insert screw (1/4-20 x
1.85 in.) through holes. 3. Place nut onto screw and tighten.
1. Pull back the quick-connect collar. 2. Push the desired
nozzle into the quick-connect collar until it clicks into place
and is secured properly.
1. Connect threaded end of spray wand to the trigger
handle. 2. Turn connector clockwise to secure spray wand.
3. Connect high-pressure hose to trigger handle inlet
coupler. 4. Turn the hose collar counterclockwise to secure
hose.
1. Connect collar of the high-pressure hose to threaded
nipple on the pump. 2. Turn the collar clockwise to tighten
the hose securely to the pump.
1. Connect threaded hose coupler to the high-pressure
cleaner water intake and tighten. 2. With the garden tap
completely off, attach the end of the garden hose adapter
(not supplied) to hose coupler.
Turn on the water supply.
1. Turn the dipstick counterclockwise to open. 2. Remove
the dipstick. 3. Fill the engine with 4-stroke engine lubricant
(SAE 10W-30) until the fluid level rises to the upper portion
of the hatched area on the dipstick. Replace the dipstick
and tighten securely.
NOTE: Check the engine oil. When the dipstick oil cap is
placed inside the filler, do not re-thread. The oil should be
visible between the minimum and maximum marks.
1. Turn the fuel cap counterclockwise to open. 2. Remove
the fuel cap. 3. Insert a clean funnel into the fuel tank then
slowly pour the fuel into the tank (1.2 L) to approximately 40
mm (1-1/2 in.) below the top of the tank neck.
NOTE: Check the fuel. Always use fresh, unleaded (91 or
higher) fuel. Fuel without fuel stabiliser added to it begins to
turn stale from 30 days onwards.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ryobi RPW3200Y bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ryobi RPW3200Y in de taal/talen: Engels als bijlage per email.

De handleiding is 10,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info