589955
12
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Installation Instructions
Before installing this appliance in an existing chimnney, we recommend that;
1. You have your chimney cleaned by a competent chimney sweep.
2. You block o the chimney  ue.
This procedure is important for the e cient operation of the heating unit and will also reduce heat loss up the chimney.
Installation.
Ensure that all packing items are removed (read any warning labels carefully).
Retain all packing for possible future use e.g. in the event of moving or returning the appliance to your supplier.
To install the appliance;
1. Clean the area where the  re will be installed e.g remove ash residue from an existing  replace.
2. Use the two adjustable supports at the rear of the appliance to ensure that the  re is level.
3. Make sure the unit is switched OFF.
4. Hold the  re by the sides of surround and gently manoeuvre into position. Plug the  re into a 13amp/240 volt outlet. Ensure
that the supply cable is not trapped under the  re such that it might cause it to be damaged.
Before using the manual controls  rstly ll the water tank (See ‘Maintenance, ‘Filling the water tank’).
Manual Controls.
The Mystic Fires manual controls are located beneath the hinged canopy. Raise the canopy to access the controls. (See Fig.2
for Manual Control lay out)
Switch A’:- Controls the electricity supply to the Fire.
Note: This switch must be in the ON’ ( I ) position for the Fire to operate either with or without heat.
Switch ‘B’:- Press
once to turn on the  ame e ect. This will be indicated by an audible beep. Although the main lights
operate immediately it will take a further 30 seconds before the  ame e ect starts.
Press again to give  ame e ect and half heat. This will be indicated by two beeps.
Press again to give  ame e ect and full heat. This will be indicated by three beeps.
Press again to return to  ame e ect only. This will be indicated by one beep.
Press to put  re in to standby mode. This will be indicated by one beep.
Control Knob ‘C’:- Controls the Thermostat setting.
Turning the control knob Anti Clockwise will decrease the temperature setting, turning the control knob Clockwise
will increase the temperature setting.
Control Knob ‘D’:- Controls the intensity of the  ame e ect.
Turning the control knob Anti Clockwise increases the  ame e ect, turning the control knob Clockwise will decrease
the ame e ect.
When the water in the tank and in the sump runs out the main lamps will go out. See instructions under ‘Maintenance, ‘Filling
the water tank’. When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the  ames
return.
Setting the Thermostat
Plug in and switch on the  re to the full heat setting. Turn the Control Knob C’ fully clockwise (max temperature setting) to
warm the room rapidly. When the room temperature has reached the desired level, turn the thermostat knob back slowly until
you hear the thermostat just click o . The heater will then maintain the room temperature at the chosen level.
Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room temperature
being higher then the thermostat setting
Thermal safety cut-out
A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if the heat
outlet was restricted in any way or if the chimney  ue has not been blocked o e ectively. If the cut-out operates, unplug the
heater from the socket outlet and allow approximately 10 minutes before reconnecting. Before switching the heater back on
remove any obstruction that may be restricting the heat outlet, then continue normal operation.
Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied
through an external switching device, such as a timer, or connected to a switch that is regularly switched on and o by the
utility.
7
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ruby Fires RF30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ruby Fires RF30 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 0,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info