9
4. USE
ASSEMBLING THE PARTS OF THE APPLIANCE
• Firmly place the tube (19) in the vacuum opening (9) and turn to screw on – fig.1.
• To withdraw the tube, turn in the opposite sense and pull – fig.2.
• If your vacuum cleaner is equipped with a telescopic tube* (20) : push the clamping button forward, extend
the tube to the desired length and release the button to lock the tube in place - fig. 3.
Otherwise, assemble the two tubes* (21) by turning slightly - fig. 4.
• Fit the tube extension* (22) if necessary.
• Fit the required accessory onto the end of the tube:
- For rugs and carpets: use the "all floors” nozzle (23) with the brush tucked in - fig. 5, or the turbo-brush* (27 or 28*).
- For wood and hard floors: use the “all floors” nozzle (23) with the brush pulled out (fig. 6) or, for best
results, use the parquet nozzle* directly (24).
- For corners and hard to reach spots: use the crevice tool convertible into brush (26) in the flat position.
- For upholstery and delicate surfaces: use the crevice tool convertible into brush (26) or the upholstery nozzle* (25),
or the brush integrated to the grip 19b* (depending on model).
Attention! Always switch off and disconnect your vacuum cleaner before changing any accessories.
PLUGGING AND SWITCHING ON THE APPLIANCE
• Unwind the power cord completely, plug in your vacuum cleaner (fig. 7) and press the ON/OFF pedal
(2) - fig. 8.
• Set the suction power using the manual power switch on the handle: open the regulation vent in order to
manually decrease the suction power, for example: on fragile surfaces –fig. 9.
STORAGE AND TRANSPORT OF THE APPLIANCE
• After each use, switch your vacuum cleaner off by pressing on the ON/OFF pedal (2) –fig. 8- and unplug it
–fig. 10. Store the cord by pressing on the wind pedal (3) - fig.11.
• In the vertical position, place the nozzle (23) in its storage compartment on the appliance (1b) – fig. 12.
• In the horizontal position, place the nozzle (23) in its storage compartment on the appliance (1a) – fig. 13.
• You may easily transport your vacuum cleaner by the transport handle (6).
5. CLEANING AND MAINTENANCE
Important: Always switch off and unplug your vacuum cleaner before maintenance or cleaning.
CHANGING THE BAG
• The Bag full indicator (4) indicates that the bag is full or saturated. If you notice a reduction of the efficiency
of your appliance, set the power at maximum and hold the nozzle above the ground. If the Bag full indicator
remains red, replace the bag.
• Remove the flexible hose (19) from the suction opening (9) - fig. 2.
• Open the lid (8) of your vacuum cleaner - fig.14
a) If your vacuum cleaner is equipped with a paper bag* :
• Remove the bag support (15) from the bag compartment (7) – fig.15a, then remove the paper bag (18a)
from its base (15) by sliding it through the runners - fig. 15b.
• Throw the bag in the rubbish bin -fig.15c.
• Place a new bag in the bag support (15) – fig. 15d, then place the base inside the compartment by sliding
it on the runners (16) –fig. 15e.
• Make sure the bag and the bag support are correctly positioned before closing the lid (8).
b) If your vacuum cleaner is equipped with a textile bag* :
• Remove the bag support (15) from the bag compartment (7) – fig.16a, then remove the textile bag (18b)
from its support (15) by sliding it through the runners - fig. 16b.
• Open the textile bag using the zipper -fig. 16c- then empty it above a rubbish bin – fig. 16d.
• Clean the bag with running water – fig. 16e.
• Leave the bag to dry for at least 24 hours (do not replace the bag until it is perfectly dry) – fig. 16f.
EN
* According to model : These parts are specific to certain models
or they are accessories that can be purchased separately.
