802897
6
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
6 7
EN
EN PROBLEMS
Problem Cause Solution
The iron is plugged in, but the
soleplate of the iron remains
cold.
No mains supply. Check that the mains plug
is properly inserted or try
plugging the iron into a
different socket.
The automatic electronic auto
off is active.
Move your iron.
None or too little steam is
being emitted.
The iron is not ready to use. Wait until the mode you have
selected stops blinking.
NB: on "Nylon" mode, the
steam output is low to
preserve your clothes.
Not enough water in the
water tank. Fill the water tank.
Anti-Drip is active Wait for the soleplate to reach
the correct temperature.
The trigger is not pressed. Press the trigger to get steam
output.
The steam is blocked on
NYLON mode in order to
protect your clothes
Select a higher mode if
needed
Brown streaks come through
the holes in the soleplate and
stain the fabric.
Residues in the steam
chamber or on the soleplate.
Use the Calc Clean Program
then clean your iron.
Do not add any descaling
agents, perfumed, or
scented additives to the
water in the water tank.
Use the Calc Clean Program
and clean your iron if you
have used the above.
Fabric fibres have
accumulated in the holes of
the soleplate and are burning.
Clean the soleplate with a
non-metallic sponge.
Your linen is not rinsed
sufficiently or you have
ironed a new garment before
washing it.
Ensure linen is rinsed
thoroughly.
Use of starch. Always spray starch onto the
reverse side of the fabric to
be ironed and clean your iron
soleplate afterwards.
Pure distilled /demineralised
or softened water is being
used.
Only use untreated tap water
or mix half tap water with half
distilled/demineralised water.
Use the Calc Clean Program
and clean your iron.
Iron is leaking. Overuse of shot of steam
trigger. Allow more time between
each shot.
Use of the shot of steam
trigger on NYLON, SILK or
WOOL modes.
Use only the steam boost on
COTTON and LINEN modes.
Use of chemical
descaling agents,
perfumed or scented
additives.
AFTER USE
8 • Emptying
Unplug the iron fig 1. Pour away remaining water fig 10.
9 • Storing
Allow the appliance to cool down for 1 hour before winding the cord around the heel. Store
the iron on its base in a dry and safe place fig 12.
IMPORTANT Do not wind the cord around the hot soleplate. Never store your iron
placed down on the soleplate.
Remove the plug from the wall socket and let the iron cool down before
maintenance and cleaning.
IMPORTANT: this program will last 4 to 6 minutes.
10 • Cleaning the iron
When the appliance has cooled down, wipe the iron down with a damp cloth or sponge. A non
abrasive cleaning agent can be used.
IMPORTANT Do not use sharp or abrasive cleaning agents or objects to clean the
soleplate and other parts of the iron.
WARNING : Do not use descaling agents even if advertised for steam irons. They will
permanently damage your iron.
MAINTENANCE AND CLEANING
11 • Calc clean program (4-6 min)
The Calc Clean System flushes dirt and scale particles out of the steam chamber.
This considerably prolongs the operational life of your iron.
Your iron needs to be cleaned when the CALC CLEAN warning light remains lighted on the
LED screen fig 11a.
If the "CALC CLEAN" light starts flashing when you are ironing, you can finish your ironing
session. There is no risk for your clothes nor the appliance.
TO START THE CALC CLEAN PROGRAM:
1. Unplug the iron (fig 1)
2. Fill in the water tank fig 2 & 3
3. Plug the iron (fig 4)
4. Put the iron over a sink or a basin
5. Press simultaneously the Mode button & the trigger for 3 secondes to start the Calc Clean
Program. (fig 11b)
The iron will start to heat up without producing steam. When arrived at the maximum
temperature, the water will start to run down fig 11c. During the process, the fabrics on the LED
screen will blink alternatively. Once the process finished, the iron will automatically shut off.
Allow the appliance to cool down and then wipe the iron down with a damp cloth or a sponge.
6 • Anti-Drip system
It prevents water dripping out of the soleplate when the temperature is too low.
7 • Auto Off function
For your safety, the electronic system cuts off the power and the auto off indicator
light flashes fig 9 when:
- The iron remains motionless for more than 8 minutes on its base
- The iron remains flat or on its side for more than 30 seconds
To restart the iron, just move it gently until the warning light stops flashing.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rowenta DW9510 Steamforce Pro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rowenta DW9510 Steamforce Pro in de taal/talen: Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 2.49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info