489964
9
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
9
English
If you are using terminal lugs, connect them to the wires. If you are
attaching bare wires directly to the speaker connectors, separate the
wire conductors and strip back the insulation from the end of each
conductor. Be careful not to cut into the wire strands. Unscrew (turn
counterclockwise) the speaker connector collar. Place the connector lug
around the shaft, or insert the bundled wire into the hole in the shaft.
Turn the collars clockwise to clamp the connector lug or wire fi rmly in
place.
NOTE: Be sure there are no loose wire strands that could touch
adjacent wires or connectors.
Troubleshooting
Most diffi culties in audio systems are the result of poor or wrong
connections, or improper control settings. If you encounter problems,
isolate the area of the diffi culty, check the control settings, determine
the cause of the fault and make the necessary changes. If you are
unable to get sound from the amplifi er, refer to the suggestions for the
following conditions:
Front Panel Power Indicator Is Not Lit
No mains power to the amplifi er. Check AC power connections at
the amplifi er and the AC outlet. Check the front panel power switch.
Make sure that it is set to the ON position. If using 12V trigger power-
on, make sure that a trigger signal is present at rear panel screw
terminals.
No Sound
If the amp is getting AC power, but is producing no sound, check
the PROTECTION INDICATOR on the front panel. If lit, see below. If
not, check all of your connections and control settings on associated
components. Make sure that your input connections and speaker
connections match your selected confi guration.
Protection Indicator Is Lit
The front panel PROTECTION INDICATOR is lit when the amplifi er
protection circuits have shut off the amplifi er. Typically, this occurs
only when the amplifi er has overheated, when there is faulty speaker
wiring, or after a period of extreme use. Turn off the system and wait
for the amp to cool. Then push the front panel power switch in and
out to reset the protection devices. If the problem is not corrected or
reoccurs, there is a problem with the system or the amplifi er itself.
Specifi cations
RMB-1565
Continuous Power Output
Continuous Power Output 100 watts/channel
(20-20 kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion
Total Harmonic Distortion (20Hz-20kHz, 8 ohms) < 0.03%
Intermodulation Distortion
Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03%
Frequency Response
Frequency Response ( ±1dB) 10Hz - 40kHz
Damping Factor
Damping Factor (20-20,000 Hz, 8 ohms) 200
Speaker Impedance
Speaker Impedance (Normal mode) 4 ohms minimum
Signal to Noise Ratio
Signal to Noise Ratio (IHF A network) 105 dB
Input Impedance/Sensitivity
Input Impedance/Sensitivity 8.2 k Ohms/1.25 volt
Power Requirements
Power Requirements 110 -240 Volts, 50-60 Hz
Power Consumption
Power Consumption 250 Watts
Dimensions
Dimensions
Width x Height x Depth 431 x 99 x 339 mm
17 x 3
7
/8 x 13
3
/8 ins.
Front Panel Height 2U
Weight
Weight (net) 6 kg, 13.23 lb.
RMB-1575
Continuous Power Output
Continuous Power Output 250 watts/channel
(20-20 kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion
Total Harmonic Distortion (20Hz-20kHz, 8 ohms) < 0.03%
Intermodulation Distortion
Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03%
Frequency Response
Frequency Response ( ±1dB) 10Hz - 80kHz
Damping Factor
Damping Factor (20-20,000 Hz, 8 ohms) 400
Speaker Impedance
Speaker Impedance (Normal mode) 4 ohms minimum
Signal to Noise Ratio
Signal to Noise Ratio (IHF A network) 109 dB
Input Impedance/Sensitivity
Input Impedance/Sensitivity 8.3 k Ohms/1.5 volt
Power Requirements
Power Requirements
U.S. version 120 Volts, 60 Hz
European version 230 Volts, 50 Hz
Power Consumption
Power Consumption 600 Watts
Dimensions
Dimensions
Width x Height x Depth 431 x 144 x 406 mm
17 x 5
11
/16 x 16 ins.
Front Panel Height 3U
Weight
Weight (net) 11 kg, 24.25 lb.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rotel RMB-1575 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rotel RMB-1575 in de taal/talen: Nederlands, Duits, Engels als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info