489974
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
10
RMB-1512 Twelve Channel Power Amplifier
Troubleshooting
Most difficulties in audio systems are the result of poor or wrong
connections, or improper control settings. If you encounter problems,
isolate the area of the difficulty, check the control settings, determine
the cause of the fault and make the necessary changes. If you are
unable to get sound from the RMB-1512, refer to the suggestions for
the following conditions:
Standby Power Indicator Is Not Lit
No main power to the RMB-1512. Check AC power connections at
the amplifier and the AC outlet. Check the front panel power switch.
Make sure that it is set to the ON position. If using signal sensing auto
power-on, make sure that a signal is present at the inputs. If using 12V
trigger power-on, make sure that a trigger signal is present at rear
panel 12V TRIG IN connector.
No Sound
If the amp is getting AC power, but is producing no sound, check the
PROTECTION INDICATORS on the front panel. If lit, see below. If
not, check all of your connections and control settings on associated
components.
Protection Indicator Is Lit
The front panel PROTECTION INDICATORS light when the RMB-1512
protection circuits have shut off the amplifier. Typically, this occurs only
when the ventilation openings are blocked,when there is faulty speaker
wiring, or after a period of extreme use. Turn off the system and wait
for the amp to cool. Then push the front panel power switch in and
out to reset the protection devices. If the problem is not corrected or
reoccurs, there is a problem with the system or the amplifier itself.
Specifications
Continuous Power Output 100 watts/channel
(20-20k Hz, <0.03% THD, 8 ohms)
Total Harmonic Distortion (20Hz -- 22Hz, 8 ohms) < 0.03%
Intermodulation Distortion (60Hz:7kHz, 4:1) < 0.03%
Damping Factor (20Hz-20kHz, 8ohms) 200
Input Impedance/Sensitivity 8.3 ohms/1.25 volts
Amplifier Gain 27.2db
Frequency Response (±1db) 10Hz - 40Khz
S/N Ratio (IHF A) 105 db
Crosstalk / Separation > 70 db
Speaker Impedance 4 ohms minimum
Auto Turn On level (with all inputs) 5mV input signal
Power Requirements USA: 120 volts, 60Hz
Europe: 230 volts, 50Hz
Power Consumption 660 watts
Idle: 84 watts
Standby: 10.8 watts
Dimensions (W x H x D) 431 x 144 x 449 mm
17 x 5.7 x 17.8 in
Weight (net) 10.9 kgs, 23.98 lbs
Panel Height 3U, 132,6 mm / 5.2 in
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rotel RMB-1512 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rotel RMB-1512 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info