Handleiding Rotel RC-06 (pagina 7 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans)

490019

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

English

Input Signal Connections

[See Figure 3.]

NOTE: To prevent loud noises that neither

you nor your speakers will appreciate,

make sure the system is turned off when you

make any signal connections.

Phono/Line Input

and

Ground Connection

The Phono/Line input is set at the factory

to operate as a phono input. If you will not

be using the phono input, this input can be

converted to a standard line level input. See

the “Converting the Phono/Line Input section of

this manual. The following information covers

using the

input as a phono input.

Plug the cable from the turntable into the ap

propriate left and right phono inputs. If the

turntable has a “ground” wire connect it to

the screw terminal

to the left of the Phono

inputs. It will help prevent hum and noise.

Line Level Inputs

The CD, Tuner, and Aux inputs of the RC-06

are “line level” inputs. These are for connect

ing components such as CD players, Hi Fi or

NICAM Stereo video cassette recorders, tuners,

Laser Disc players or the analog output from

a CD ROM drive.

The Left and Right channels are labeled and

should be connected to the corresponding

channels of the source component. The Left

connectors are white, the Right connectors

are red. Use high quality RCA cables for

connecting input source components to the

RC-06. Ask your authorized Rotel dealer for

advice about cables.

Phono/Line Input Conversion

[See Figure 2 for conversion jumper

locations.]

The Phono/Line input set conﬁgured at the

factory for phono input operation. If you do

not use the phono input and need another line

level input, this input can be converted to a

standard line level input.

In order to convert the input for line level usage,

four “jumper” connectors inside the RC-06 must

be moved from one set of pins to another. This

task should be done by a qualiﬁed technician.

See your authorized Rotel dealer.

Resetting Jumpers

Before opening the RC-06 cabinet to re-

set the jumpers, the power cord must be

unplugged from the wall. DO NOT OPEN

THE CABINET OF THE RC-06 BEFORE THE

POWER CORD HAS BEEN UNPLUGGED

FROM THE WALL. FAILURE TO DO SO WILL

EXPOSE YOU TO HAZARDOUS VOLT

AGES.

After the power cord has been unplugged,

remove the screws that hold the cabinet cover

in place and slide the cover off. Locate the

four jumper pin blocks near the Phono/Line

input labeled SW1, SW2, SW3 and SW4.

The factory standard (phono) position of the

jumpers is on pins 2 and 3 of each block. To

convert the RC-06 Phono/Line input to a line

type input move all four jumpers so they are

on pins 1 and 2 of each jumper pin block.

Replace the cover of the cabinet. Do not

plug the RC-06 power cord back into

the wall outlet until the cabinet cover

has been replaced.

Recorder Connections q

[See Figure 3.]

The Tape inputs and outputs can be connected

to any record/playback device that accepts

standard line level analog input and output

signals. Typically that will be a conventional

tape recorder.

When connecting a recorder to the RC-06

remember that the outputs of the recorder must

be connected to the tape inputs of the RC-06.

Similarly the tape outputs of the RC-06 must

be connected to the inputs of the recorder. As

with other sources be sure to connect the Left

and Right channels of each device to the proper

channels on the associated components. Use

high quality connecting cables to prevent loss

of sound quality.

NOTE: The Tape Outputs are not affected

by the Volume or Balance controls. They

receive a fixed level signal.

Output Connections w

[See Figure 3.]

The RC-06 has RCA-type output connectors

that are compatible with the inputs of most

power ampliﬁers. Use high quality cables and

be sure to connect the Left and Right channel

outputs of the RC-06 to the correct channels

of the ampliﬁer.

There are two sets of outputs on the RC-06. The

second set of outputs may be used in custom

system conﬁgurations to drive a second power

ampliﬁer or to supply a signal to a special

signal processor.

NOTE: Changes to the settings of the

Volume and Balance controls affect the

signal from the Preamp Outputs.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Rotel RC-06 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info