Handleiding Rossmax MW-821F (pagina 1 van 2) (Engels)

783823

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

www.rossmax.com

Instruction Manual

Model: MW821 f

The National High Blood Pressure Education Program Coordinating

Committee has developed a blood pressure standard, classifying blood

pressure ranges into 4 stages. (Ref. The Sev-

enth Report of the Joint National Committee

on Prevention, Detection, Evaluation, and

Treatment of High Blood Pressure-Complete

Report JNC-7, 2003).This blood pressure

classification are based on historical data,

and may not be directly applicable to any

particular patient. It is important that you

consult with your physician regularly. Your

physician will tell you your normal blood

pressure range as well as the point at which

you will be considered at risk. For reliable

monitoring and reference of blood pressure,

keeping long- term records is recommended.

Please download the blood pressure log at

www.rossmax.com.

Attention: Consult the accompanying documents. Please read this

manual carefully before use. For specic information on your

own blood pressure, contact your physician. Please be sure

to keep this manual.

Blood pressure measurements determined with MW821f are equivalent to

those obtained by a trained observer using cuff/stethoscope auscultation

method, within the limits prescribed by the American National Standard,

Electronic or Automated Sphygmomanometers. This unit is to be used by

adult consumers in a home environment. Do not use this device on infants

or neonates. MW821f is protected against manufacturing defects by an

established International Warranty Program. For warranty information,

you can contact the manufacturer, Rossmax International Ltd.

1. Introduction

3. Real Fuzzy Measuring Technology

4. Preliminary Remarks

This unit uses the oscillometric method to detect your blood pressure. Be-

fore the cuff starts inating, the device will establish a baseline cuff pres-

sure equivalent to the air pressure. This unit will determine the appropriate

ination level based on pressure oscillations, followed by cuff deation.

During the deation, the device will detect the amplitude and slope of

the pressure oscillations and thereby determine for you the systolic blood

pressure, diastolic blood pressure, and pulse.

This Blood Pressure Monitor complies with the European regulations and

bears the CE mark “CE 0120”. The quality of the device has been veri-

ed and conforms to the provisions of the EC council directive 93/42/

EEC (Medical Device Directive), Annex I essential requirements and applied

harmonized standards.

EN 1060-1: 1995/A2: 2009 Non-invasive sphygmomanometers

- Part 1 - General requirements

EN 1060-3: 1997/A2: 2009 Non-invasive sphygmomanometers

- Part 3 - Supplementary requirements for electro-mechanical blood pres-

sure measuring systems

EN 1060-4: 2004 Non-invasive sphygmomanometers

- Part 4: Test Procedures to determine the overall system accuracy of auto-

mated non-invasive sphygmomanometers.

This blood pressure monitor was designed for long service time. To en-

sure continued accuracy, it’s recommended that all digital blood pressure

monitors require re-calibration. This monitor (under normal usage with

approx. 3 measurements a day) does not require re-calibra-

tion for 2 years. Once the unit should be re-calibrated the

device will display . The unit should also be re-calibrated

if the monitor sustains damage due to blunt force (such as

dropping) or exposure to uids and / or extreme hot or cold

temperature / humidity changes. When appears, simply

return to your nearest dealer for re-calibration service.

7. Display Explanations

Blood pressure uc-

tuates all the time!

You should not be

overly worried if you

encountered two or

three measurements

at high levels. Blood

pressure changes over

the month and even

throughout the day.

It is also inuenced

by season and tem-

perature.

5. Blood Pressure Standard

6. Blood Pressure Fluctuation 11. Installing Batteries

11. Using the Talking Function

1. Press down and lift the battery cover in

the direction of the arrow to open the

battery compartment.

2. Install or replace 4 “AA” sized batteries

in the battery compartment according

to the indications inside the compart-

ment.

3. Replace the battery cover by clicking

in the bottom hooks rst, then push in

the top end of the battery cover.

4. Replace the batteries in pairs. Remove batteries when unit is not in use for

extended periods of time.

You need to replace the batteries when

1. low battery icon appears on display.

2. the ON/OFF/START key is pressed and nothing appears on display.

Caution

1. Batteries are hazardous waste. Do not dispose them together with the house-

hold garbage.

2. There are no user serviceable parts inside. Batteries or damage from old bat-

teries are not covered by warranty.

3. Use exclusively brand batteries. Always replace with new batteries together.

Use batteries of the same brand and same type.

1. Select English or Spanish by pressing the Language

Selection key labelled with an “L” and located on

the back of the unit.

•”L1” will appear on the display for English.

•”L2” will appear on the display for Spanish.

2. Turn the talking feature on (or off) by pressing the

Speaker ON/OFF key located on the front of the unit.

2. Name/Function of Each Part

1. Unwrap the arm cuff, leaving the end of the cuff through the D-ring

of the cuff.

2. Put your left arm through the cuff loop. The color strip indication

should be positioned closer to you with the tube pointing in the direc-

tion of your arm (Fig. 1). Turn your left palm upward and place the

edge of the arm cuff at approximately 1.5 to 2.5 cm above the inner

side of the elbow joint (Fig. 2). Tighten the cuff by pulling the end of

the cuff.

3. Center the tube over the middle of the arm. Press the hook and loop

material together securely. Allow room for 2 fingers to fit between the

cuff and your arm. Position the artery mark (Ø) over the main artery (on

the inside of your arm) (Fig. 3,4).

Note: Locate the main artery by pressing with 2 fingers approximately

2 cm above the bend of your elbow on the inside of your left arm.

Identify where the pulse can be felt the

strongest. This is your main artery.

The National High Blood Pressure Educa-

tion Program Coordinating Committee

has developed a blood pressure stand-

ard, classifying blood pressure ranges

into 4 stages. This unit is equipped with

innovative blood pressure risk indicator,

which visually indicates the assumed risk

level (prehypertension / stage 1 hyper-

tension / stage 2 hypertension) of the

result after each measurement.

This unit is equipped with an Irregular Heart-

beat Detector (IHB) which allows those who

have an irregular heartbeat to obtain accurate

measurements alerting the user of the pres-

ence of an irregular heart beat during the

measurement.

Note: It is strongly recommended that you

consult your physician if the IHB icon

() appears often.

12. Applying the Cuff

8. Hypertension Risk Indicator

9. Irregular Heartbeat Detector (IHB)

1. Hypertension Risk Indicator

2. Memory Zones

3. Speaker Mark

4. Memory Average

5. Weak Battery Mark

6. Date/Time Indicator

7. Irregular Heartbeat (IHB) Detector

8. Systolic Pressure

9. Diastolic Pressure

10. Pulse Rate

11. Pulse Mark

Fig.1

Fig.3

Fig.2

Fig.4

Fig.5

Fig.7

Fig.6

4“AA”(R06) size,

1.5V batteries.

1. Connect the AC adapter with the AC adapt-

er jack in the back of the unit.

2. Plug the AC adapter into the socket. (AC

adapters with required voltage and current

indicated near the AC adapter jack.)

Caution: 1. Please unload the batteries when

operating with the AC mode for

a longer period of time . Leaving

the batteries in the compartment

for a long time may cause leakage,

which may lead to damage of the

unit.

2. No batteries are needed when operating with the AC mode.

3. AC adapters are optional. Please contact the distributor for

the compatible AC adapters.

4. Use only the authorized AC Adaptor with this blood pressure

monitor. Information for the authorized AC adaptor, please

refer to APPENDIX 1.

10. Using the AC Adapter (Optional)

AC Adapter

(Ø4.0/Ø1.7)

Arm Cuff

Date/Time

Set Key

LCD Display

User-Switching Key

ON/OFF/START Key

Memory Key

Air Tube and

Connector

Battery Cover

(Located on

back of unit)

Data Link Socket

AC Adapter

Jack

Speaker

ON/OFF key Speaker

Language

Selection key

Language Selection key

"L1" is English "L2" is Spanish Speaker ON/OFF key

Measurement Error: Make sure the L-plug is securely con-

nected to the air socket and measure again quietly. Wrap the

cuff correctly and keep arm steady during measurement. If the

error keeps occurring, return the device to your local distribu-

tor or service center.

Air Circuit Abnormality: Make sure the L-Plug is securely

connected to the air socket on the side of the unit and meas-

ure again quietly. If the errors still occur, return the device to

your local distributor or service center for help.

Pressure Exceeding 300 mmHg: Switch the unit off and

measure again quietly. If the error keeps occurring, return the

device to your local distributor or service center.

Data Error: Remove the batteries, wait for 60 seconds, and

reload. If the error keeps occurring, return the device to your

local distributor or service center.

Exceeding Measurement Range: Measure again quietly. If

the error keeps occurring, return the device to your local dis-

tributor or service center.

Rossmax MW-821F Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info