Handleiding Rossmax AC1000f (pagina 16 van 19) (Engels)

712109

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

30 31

Guidance and manufacturer’s declaration-electromagnetic emissions

The AC1000f is intended for use in the electromagnetic environment specied below. The customer or the user of

the AC1000f should assure that it is used in such an environment.

Emission test Compli-

ance

Electromagnetic environment-guidance

RF emissions CISPR 11 Group 1 The AC1000f uses RF energy only for its internal function.

Therefore, its RF emissions are very low and are not likely to

cause any interference in nearby electronic equipment.

RF emissions CISPR 11 Class B The AC1000f is suitable for use in all establishments, including

domestic establishments and those directly connected to the

public low-voltage power supply network that supplies build-

ings used for domestic purposes.

Harmonic emissions IEC 61000-3-2 Class A

Voltage uctuations/icker emissions

IEC 61000-3-3

Compli-

ance

Guidance and manufacturer’s declaration-electromagnetic immunity

The AC1000f is intended for use in the electromagnetic environment specied below. The customer or the user of

the AC1000f should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment-

guidance

Electrostatic dis-

charge (ESD) IEC

61000-4-2

± 6 kV contact

± 8 kV air

± 6 kV contact

± 8 kV air

Floors should be wood, concrete

or ceramic tile. If oors are covered

with synthetic material, the relative

humidity should be at least 30%

Electrical fast

transient/burst

IEC 61000-4-4

± 2kV for power supply

lines

± 1kV for input / output

lines

± 2kV for power supply

lines

Not applicable

Mains power quality should be that

of a typical commercial or hospital

environment.

Surge IEC

61000-4-5

± 1kV line(s) to line(s)

± 2kV line(s) to earth

± 1kV differential mode

Not applicable

Mains power quality should be that

of a typical commercial or hospital

environment.

Voltage Dips,

short interrup-

tions and voltage

variations on

power supply

input lines IEC

61000-4-11

<5% UT(>95% dip in UT)

for 0,5 cycle

40% UT(60% dip in UT)

for 5 cycles

70% UT(30% dip in UT)

for 25 cycles

<5% UT(>95% dip in UT)

for 5 s

<5% UT(>95% dip in UT)

for 0,5 cycle

40% UT(60% dip in UT)

for 5 cycles

70% UT(30% dip in UT)

for 25 cycles

<5% UT(>95% dip in UT)

for 5 s

Mains power quality should be that

of a typical commercial or hospital

environment. If the user of the

AC1000f requires continued opera-

tion during power mains interrup-

tions, it is recommended that the

AC1000f be powered from an unin-

terruptible power supply or a battery.

Power frequency

(50/60 Hz) mag-

netic eld IEC

61000-4-8

3 A/m 3 A/m Power frequency magnetic elds

should be at levels characteristics of

a typical location in a typical com-

mercial or hospital environment.

NOTE: UT is the a.c. mains voltage prior to application of the test level.

Recommended separation distance between portable and mobile RF communications equipment and the

AC1000f

The AC1000f is intended for use in an electromagnetic environment in which radiated RF disturbances are con-

trolled. The customer or the user of the AC1000f can help prevent electromagnetic interference by maintaining a

minimum distance between portable and mobile RF communications equipment (transmitters) and the AC1000f

as recommended below, according to the maximum output power of the communications equipment.

EMC guidance and manufacturer’s declaration EMC guidance and manufacturer’s declaration

Rated maximum output

power of transmitter / W

Separation distance according to frequency of transmitter / m

150 kHz to 80 MHz d =

1,2 √P

80 MHz to 800 MHz d =

1,2 √P

800 MHz to 2,5 GHz d =

2,3 √P

0,01 0,12 0,12 0,23

0,1 0,38 0,38 0,73

1 1,2 1,2 2,3

10 3,8 3,8 7,3

100 12 12 23

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in

metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the

maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption

and reection from structures, objects and people.

Guidance and manufacturer’s declaration-electromagnetic immunity

The AC1000f is intended for use in the electromagnetic environment specied below. The customer or the user of

the AC1000f should assure that is used in such and environment.

Immunity

test

IEC 60601 test

level

Compliance

level

Electromagnetic environment-guidance

Conducted

IEC 61000-

4-6

Radiated RF

IEC 61000-

4-3

3 Vrms

150 KHz to 80

MHz

3 V/m

80MHz to 2,5

GHz

3 Vrms

3 V/m

Portable and mobile RF communications equipment should be used

no closer to any part of the AC1000f including cables, than the

recommended separation distance calculated from the equation ap-

plicable to the frequency of the transmitter.

Recommended separation distance:

d = 1,2 √P, d = 1,2 √P 80MHz to 800 MHz, d = 2,3 √P 800MHz to

2,5 GHz

Where P is the maximum output power rating of the transmitter in

watts (W) according to the transmitter manufacturer and d is the

recommended separation distance in metres (m).

Field strengths from xed RF transmitters, as determined by an elec-

tromagnetic site survey, a should be less than the compliance level in

each frequency range. b

Interference may occur in the vicinity of equipment marked with the

following symbol:

NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption

and reection from structures, objects and people.

a: Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and land

mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically

with accuracy. To assess the electromagnetic environment due to xed RF transmitters, an electromagnetic site

survey should be considered. If the measured eld strength in the location in which the AC1000f is used exceeds

the applicable RF compliance level above, the AC1000f should be observed to verify normal operation. If ab-

normal performance is observed, additional measures may be necessary, such as re-orienting or relocating the

AC1000f.

b: Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.

Rossmax AC1000f Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info