Handleiding Roland XV-2020 (pagina 72 van 169) (Engels)

647722

Verklein

Vergroot

Pagina terug

1/169

Pagina verder

Creating a Performance

SOLO

(Solo Part Select)

Refer to the Performance Common column

Parameter Value Description

TYPE

(Part Type)

PAT, RHY Select the type of sound the Part plays.

GROUP

(Part Group)

USER, PR-A–D, GM,

EXP-A, EXP-B

Chooses the group (Bank) to which the desired Patch or Rhythm Set belongs.

* It is not possible to choose EXP-A, EXP-B unless a wave expansion board is insert-

ed into the corresponding slot. (p. 105)

NUMBER

(Patch/Rhythm Set Number)

Chooses the Rhythm set number to which the desired Patch or Rhythm Set be-

longs.

LEVEL

(Part Level)

0–127 Sets the volume of the Part. This setting’s main purpose is to adjust the volume

balance between Parts.

PAN

(Part Pan)

L64–63R Specifies the stereo position of the Part’s sound. L64 pans the sound hard left,

0 puts it dead-center and 63R pans it hard right.

VEL SENS

(Part Velocity Sensitivity)

-63–+63 Raises or lowers the VELOCITY V-Cutoff and the TVA V-Sens settings for

each of the Tones in the Part’s sound.

OCT SHIFT

(Part Octave Shift)

-3–+3 Adjusts the pitch of the Part’s sound up or down in units of an octave (+/-3

octaves).

COARSE TUNE

(Part Coarse Tune)

-48–+48 Adjusts the pitch of the Part’s sound up or down in semitone steps over a

range of +/-4 octaves.

FINE TUNE

(Part Fine Tune)

-50–+50 Adjusts the pitch of the Part’s sound up or down in 1-cent steps (1/100th of a

semitone) over a range of half a semitone up or down.

Parameter Value Description

PB RANGE

(Part Pitch Bend Range)

0–24, PAT Specifies the amount of pitch change that occurs when you move the Pitch Bend Le-

ver. This overrides the sound’s own pitch-bend settings. The amount of pitch change

downward or upward that occurs when the lever is moved is the same for both its left

and right directions (or down and up on some MIDI controllers). When PATCH is

chosen, the bend range settings for the assigned Patch take effect.

MONO/POLY

(Part Mono/Poly)

MONO, POLY, PAT Sets how the Patch’s notes play. The MONO setting is effective when playing a solo

instrument Patch such as sax or flute.

MONO: Only one note sounds at a time.

POLY: Two or more notes can be played simultaneously.

PAT: The Part uses the Patch’s Mono/Poly setting.

LEGATO

(Part Legato Switch)

OFF, ON, PAT Turn this parameter ON when you want to use the Legato feature and OFF when you

don’t. Legato is a feature that works only when the Key Assign Mode is MONO. When

Legato is ON, pressing one key when another is already pressed causes the currently

playing note’s pitch to change to that of the newly pressed key while continuing to

sound. This can be effective when you wish to simulate performance techniques such

as a guitarist’s hammering on and pulling off strings. When PAT is selected, the

Patch’s own settings take effect.

PORTAMENT SW

(Part Portamento Switch)

OFF, ON, PAT Specifies whether the portamento effect is applied (ON) or not (OFF). When PAT is se-

lected, the settings for the assigned Patch take effect.

[What is Portamento?]

Portamento is an effect that smoothly changes the pitch from the first-played key to

the next-played key. When Key Assign is MONO, applying portamento produces an

effect similar to the slide performance technique of a violinist. Portamento can also be

applied when Key Assign is polyphonic (POLY).

PORTAMENT TIME

(Part Portamento Time)

0–127, PAT Specifies the time over which the pitch changes. Higher settings cause the pitch

change to the next note to take more time. When PAT is chosen, the settings for the

assigned Patch take effect.

VIBRATO RATE

(Part Vibrato Rate)

-64–+63 Adjusts the vibrato speed (the rate at which the pitch is modulated). The pitch will be

modulated more rapidly for higher settings and more slowly with lower settings.

VIBRATO DEPTH

(Part Vibrato Depth)

-64–+63 Adjusts the depth of the vibrato effect (the depth at which the pitch is modulated). The

pitch will be modulated more greatly for higher settings, and less with lower settings.

VIBRATO DELAY

(Part Vibrato Delay)

-64–+63 Adjusts the delay time until the vibrato (pitch modulation) effect begins. Higher set-

tings will produce a longer delay time before vibrato begins, while lower settings pro-

duce a shorter time.

Parameter Value Description

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Roland XV-2020 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info