167805
25
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
25
FRONT PANEL
R4100N
R4100N
R4100N
ON OFF
°
180 0
PHASE
POWER
PROTECT
HIGH PASS
LOW PASS
400HZ 40Hz
10Hz 400HZ
HP FULL
9V 0.2V
LEVEL BP
CH1/2
0.2V 9V
FULL
40Hz 400HZ 10Hz 400HZ
HP
CH3/4
BP
PHASE
LOW PASS HIGH PASS
LEVEL
CH4
CH3
CH2
CH1
REAR PANEL
R4100N
B C D E F G
H I J K L M N
Q R SO P
3. mOUNTING Of THE AmPLIfIER
The amplifier must NOT be mounted directly to the
chassis ground of the vehicle, this may cause to ground
loops with loud hum noise.
3.2 MINIMUM IMPEDANCE LOAD
The output stages of the RODEK amplifiers are designed to give
you extraordinary output power into 4 or 2 ohms loads in normal
stereo configurations. In bridged mode, the minimum impe-
dance load is 4 ohms. The amplifier might suffer from thermal
shut-down or even damage, if these recommended minimum
impedance load ratings are not considered appropriately. The
R1900N is stable into 1 ohm.
Before you attempt the installation of your RODEK amplifier,
it is recommended to map out the complete audio system and
the respective wiring required. Please note that - because of
possible interference problems with the existing car electrics
and electronics - especially the routing of the signal cables and
the chassis ground connection will have a profound impact on
the performance of the overall system. Secondly, the correct
mounting location needs your attention too (proper cooling
of the amp!). Use only quality installation material and if you
have only little or no experience with complex car audio instal-
lations, we strongly recommend you to consult your nearest
authorized RODEK dealer/installer.
3.1 MOUNTING LOCATION
The mounting location should be carefully selected, preferably
in the trunk compartment of your car! In the interest of passive
driver and passenger safety, the amplifier must be securely
mounted, and special precautions must be taken to allow suf-
ficient cooling. The amp can get quite hot during operation, so
a clearance of at least 5cm from both sides and from the top of
the amp must be considered.
Furthermore, the 2-/4-channel models feature an internal fan,
so the side panels must not be covered to allow for a good air
flow in and out of the side-panels windows.
Make sure there is no wiring harness, fuel tank etc. behind or
below the mounting surface that may be damaged by the dril-
ling of the holes for the amplifier mounting screws. The above
mentioned clearance of at least 5cm
to all sides of the amplifier
is not only for proper cooling, but also because the crossover
controls must remain accessible.
Ro 1-2-4-CH Manual_D+E def.indd 25 01.03.2006 10:55:37 Uhr
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rodek r 1900 n bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rodek r 1900 n in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info