512484
95
Verklein
Vergroot
Pagina terug
1/268
Pagina verder
EN
41
Message
Displayed
Probable Cause/Event Corrective/User Action
- An unknown fault has occurred and user
help is required
- Manually drive/carry the mower away
from this particular area and restart
operation.
Start elsewhere
- Drive wheel motors have been working
under a severe load during automatic or
manual operation.
- Check to insure the mower is not stuck,
allowing the drive wheels to slip.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off.
- Check the drive wheels are free to
rotate and nothing block them.
- Remove the mower away from this
particular point and restart operation.
Start inside
- Automatic operation is initiated while
Robomow is placed out of the perimeter wire
lope.
- Place the mower inside the lawn and
press the ‘GO’ button.
- Robomow get stuck in place with no succeed
to continue driving.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off
– especially in the area close to the
perimeter, where the Robomow turns in
place.
Stuck in place
- Robomow has difficulty to turn in place
because the front wheel has fallen into hole
or indention and it caused the mower to turn
in place without detecting wire or bumper.
- Confirm the area is not too sloppy and
make sure to work in dry condition.
- Check the perimeter wire is not too
close to the edge – remove if required.
- Conform the mowing deck is not set too
low.
- There is an option to drive back to the
lawn in reverse before Robomow
perform the turn in place (contact your
service dealer for details).
Switch off
before lifting
- The user carries Robomow manually while
the main switch button is on.
- Switch off the main switch button before
carrying Robomow.
Switch off
before lifting
(While Robomow is
in the Base Station)
- Robomow does not detect the power from
the base Station, there is a charging problem
- Check the connection of the Base
Station board cables (red and black) to
the Base Station pins; confirm the
screws are tightened.
- Confirm good contact between
Robomow and the Base Station
charging pins.
- Make sure the pins are clean and not
corroded.
Time and date
- Displayed every time the batteries fuse is
taken out of the mower (reset operation)
- Set real time clock (day and hour) and
the date.
Time completed
- The operating time set for that zone has
been reached.
- Connect to the charger if all mowing has
been completed for the day.
Waiting for
signal…
- Robomow has stopped the operation,
because there is no signal detected.
- Check the power to the Base Station.
- There is electrical power interruption.
There is no need to do anything –
Robomow will renew automatically the
operation if the power will come back
within an hour from the break; if the
power will come back after more than
one hour, Robomow will drive back to
the Base Station for charging, but will
not renew the operation and mowing.
95

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Robomow-Tuscania-500

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow Tuscania 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow Tuscania 500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 9,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info