512484
89
Verklein
Vergroot
Pagina terug
1/268
Pagina verder
EN
35
3.5 Operation in Base Zone – Manual Start
Manual Depart mode can be used in cases such as the following:
- Mowing the lawn at times other than when programmed.
- When the lawn is occupied and the yard must be cleared of debris, objects, pets or people first.
For initiating a manual start for mowing, press the ‘GO’ button once. Robomow will depart from the
Base Station and will mow the edge until it reaches the Base Station. It will reverse out and move
back to continue mowing of the inner area.
To skip the edge mowing process, press the ‘GO’ button twice when initiating manual start and
mowing.
3.6 Returning to the Base Station
Automatic Return
Robomow automatically returns to the Base Station at the end of every operation. It will recharge
and stay ready for the next scheduled start time that was scheduled.
Go to base’ option
You can manually send the mower to the Base Station from any point in the lawn by pressing the
upper scroll arrow once for the
Go to base’ message option - then press ‘GO’. The Robomow will
find the perimeter wire and will follow it until reaching the Base Station –
‘Searching base’
message is displayed during this sequence.
3.7 Operation in None-Base Zone
Non-Base Zone is defined as a separated area, where the user must drive the mower manually from
the Base Station or carry it by hand, to the area in order to mow it. It can be operated either by the
Perimeter Switch or the Base Station.
Important! When mowing in non-Base zone, it is required first to define the work time (refer to 2.1.2)
and to set the proper time depends on the zone area.
Zone activation
Connected to the Base Station - the zone is activated automatically as the mower is taken out from
the Base Station. If an intermittent beeping is heard shortly after turning the switch on, there is a
problem of cut wire or poor wire splicing (refer to chapter 4 – Text messages and Troubleshooting
for further help). Listen to the beeps to identify the problem (refer to figure 1.24). You must correct
the problem before Robomow can operate automatically.
Connected to Perimeter Switch
- Robomow cannot operate unless the Perimeter Switch is turned
on. Press the
on/off button to turn on the switch. To verify switch operation, there is a green LED
located next to the button that will flash when operating properly. If an intermittent beeping is heard
shortly after turning the switch on, there is a problem of cut wire or poor wire splicing (refer to
chapter 4 – Text messages and Troubleshooting for further help). Look to see which of the red
LEDs is flashing to identify the problem (refer to figure 1.43). You must correct the problem before
Robomow can operate automatically.
Place the mower inside the active perimeter.
Press the ‘GO’ button. In a case where you have forgotten to turn on the Perimeter Switch, a ‘No
wire signal’ message will be displayed, reminding you to turn the switch on.
3.8 Completing the Operation
Base Station Zone –
When Robomow has operated the allotted time, it will switch off the mowing motor and will start
moving in lines towards one of the lawn edges, then it will follow the perimeter wire back to the Base
Station, to be charged and get ready for the next operation.
89

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Robomow-Tuscania-500

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow Tuscania 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow Tuscania 500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 9,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info